6. How large of a square may be milled on the end of a 2 1/2-inch bar of round stock? Page #

Q: Determine the angle of twist, ϕB, experienced by the rod at point B. Express your answer to three…

A:

Q: Expandable pattern is used in ?

A:

Q: It is a widely use tool for laying out squaring and checking work.It consists is a square head and a…

A: following is the answer to the above question-

Q: Problem #5 The moment of inertia I of a cheap door of mass M=4.00 kg (about an axis going through…

A: given: mass of dart m=0.3 kg speed of dart v= 20 m/s width of dart R= 0.96m I =moment of inertia of…

Q: STATICS 1. Three bars, hinged at A and D and pinned at B and C as shown, form a four-link mechanism.…

A: Dear student, The above three questions are completely different not interconnected with each other.…

Q: is this drawing metric or inch?

A: In the given drawing, the screw size is M8 x 1.25 . That means is it 8 mm nominal size screw. That…

Q: what is the cutting speed of a shaper having 80 strokes per minute with a length of a stroke at 1.25…

A: Given data, S = 80 stroke/min L = 1.25 feet = 15 in Find Cutting speed = V

Q: 16. The figure below shows three different arrangements of materials 1, 2, form a wall. The thermal…

A: Given∆T=20°C k1>k2>k3

Q: 1. Draw the projection of a point “A" which is present 40 mm above HP and 30 mm in front of VP.

A:

Q: Deep sea pipelines are used to transport oil and gas across large distances, at depths greater than…

A: height of the pipe, h = 2000 mrmin = 400 mdiameter of the pie, d = 24 inch = 240.0254 = 0.6096 mt=…

Q: Find the end mill diameter for slotting operation by a cutting speed of 16 meter /minute and spindle…

A: Given details: Cutting speedVc=16meter/minSpindle speedn=275rpmformula used : Vc=πdn1000

Q: 1. Draw the projection of a point “A" which is present 40 mm above HP and 30 mm in front of VP.

A: GIVEN DATA - POINT A GIVEN , 40mm ABOVE HP AND 30mm FRONT OF VP

Q: 5. A pressure gage 7.0 m above the bottom of a tank containing a liquid reads 64.94 kPa; another…

A:

Q: In the scale of inches, draw material edge at 7.00 diameters with six holes at 50 diameters. The six…

A:

Q: 1. A turbine is rated at 600 hp when the flow of water through it is 0.61 m/s. Assuming an…

A:

Q: 2. Shown below is the binary lead-tin phase diagram from your textbook. Answer the questions below.…

A: a. Proeutectic composition is calculated at the temperature just above eutectic line of 183°C As the…

Q: In Vernier caliper, depth bar/ rod is used for * .measuring (ihäi 1)

A:

Q: 3) Docs the nodal point have the maximum or minimum stresses along the shaft, why?

A: We have given the problem

Q: For the quick-return mechanism shown below, the rod DC rotates with a constant angular velocity of 1…

A: For the solution refer below images.

Q: 150* 6. The component above requires equally spaced slots 2-1/2" apart over a 150" span. How many…

A:

Q: How do you solve parts a,b and c?

A:

Q: Find the force in member AB D E 4m a. 2kN compression b. 4kN Compression O c. 2kN tension O d. 4kN…

A:

Q: Find the end mill diameter for slotting operation by a cutting speed of 18 meter /minute and spindle…

A:

Q: Match each drawing to the term that describes it. Answers are used only once. NOTE: I asked this…

A:

Q: Find the end mill diameter for slotting operation by a cutting speed of 16 meter /minute and spindle…

A:

Q: the main diference between the prick punch and center punch?

A: Prick punch is a mechanical tool, which is made up of steel and it is used to mark points on the…

Q: What would a .010 - .020 cutback of a 14.500 Diameter be?

A: Given, Diameter, d= 14.500 mm  Range of cutback: c~ 0.010 - 0.020

Q: 3. The velocity of the water in the stream is 1.2 m/s. What is the height of the water in the pitot…

A: The height of the water in a pitot tube can be determined using Bernoulli's equation, which relates…

Q: Determine the distance h of the symmetric beam cross section to the locate the centroid given that…

A:

Q: STATICS AND STENGITH OF MATERIALS Question: Express force Fas a Cartesian vector, then determine its…

A: Given: F = 600 lb a = 1.5 ft b = 5 ft c= 3 ft theta = 60 deg

Q: What size hole was drilled in part? Would it be 3/16?

A: Solution:

Q: A 2120 lb weight is attached to a 3.4-ft-wide gate that can pivot about the hinge The weight is at a…

A:

Q: Given a workpiece below all dimension are in inches. Determine: (a) the taper length of section A,…

A: Given : To find :  (a) the taper length of section A, (b) the degree setting to taper turn section…

Q: What steps are required to draw and use Mohr’s circle?

A: Given Data⇒Mohr circleProblem definition⇒What steps are required to draw and use Mohr’s circle?