#7(0,201)DR Vø.28×90* ,250-20UNC-2B 0.312DR VØ50x82* #3(0.213)DR V.75t.06 Vø.28x90 .250-28UNF-2B V.62 0.312DR LSF D,875V.03-.06 .50 .62 1.12 (1,75) (.75) 38 1.38 2.75 3.50 .50 2.12 3.12 ø.312DR p.500 V.25±.06 0.219DR VØ.28x90° .250-32UNEF-2B UNSPECIFIED TOLERANCES MATERIAL 2-PL DEC IN.(x.xx>±.01 ,75 x 1.75 × 3.75 HRS AISI 1020 THIRD ANGLE PROJECTION REDRAWN BY "M. ZOKVIC DWN BY SCALE 11 CHKD LS 3-PL DEC IN.Cx.xxx)±,005 R. PROSINECKI TITLE DWG NO. +010 -002 HOLE TEST BLOCK 21A044 DRILLED HOLES ANGLE +0 30'

Q: I need answers to parts 10, 11, and 12, pertaining to the print provided.

A: Hii,thanks for the question but there is only 10th  question so we are answeering only 10th…

Q: What is the class of fit of a ½-20 UNF-2B thread?

A: The united thread series is classified into coarse threads, fine threads and extra fine threads. The…

Q: Refer to drawing 21A044, How many full threads will the fine tapped hole contain at minimum depth…

A: A standard thread form and series, along with allowances, tolerances, and designations, for screw…

Q: If the pitch of a thread is 1/18 inch, how many threads are needed for the threaded section of a…

A:

Q: just to clarifay is the shaft stainless steel? or the tool making the threads on the shaft

A: It is the shaft which is made up of stainless steel.

Q: I need the answers to this question.

A: The explanation of the above terms have been explained below.

Q: I need help with this.

A: Note:We’ll answer the first question since the exact one wasn’tspecified. Please submit a new…

Q: Would a 0.010" or 0.031" tool nose radius be stronger

A:

Q: Which drawing of the spindle assembly is sectioned in accordance with AS 1100?

A:

Q: What is the direction of the threads?  RH??

A: Right-hand threads run in a clockwise course, while left-hand threads (as seen in our extend of…

Q: What size UNF bolt made from SAE grade 5 steel is needed to carry a static tensile load of 3000lb…

A:

Q: Can you give a more detailled explanation for part C and answer to the following question please:…

A: Given

Q: Design and draw a channel jig for mild steel components, as in figure below, to drill a hole of 18…

A: To design and draw the channel jig for mild steel components

Q: diameter? 9. How deep is the counterbore? 1. Approximately how long is the tapped hole? . What does…

A: 10. Approximately how long is the tapped hole

Q: A long workpiece, with the length-to-dimeter ratio that exceeds factor 10, is to be machined. Which…

A:

Q: Explain the major diameter of a thread.

A: A thread can be defined as the ridge which is wrapped around the cylinder. The wrapping can be in…

Q: 1. Under what conditions are straight, or non-tapering, pipe threads used?

A: Here is the solution of your question:-Explanation:Straight or non-tapering pipe threads are…

Q: the various parts? 13. What is the tolerance on "F," the chamfer angle? 13 14. How square must the…

A: 13. 6 ° is the tolerance on "F" the chamfer angle As 20° - 14° = 6°    14. square must the ends of…

Q: What form of screw thread is most commonly used in japan?

A: The most commonly used screw thread form in Japan is the metric thread system, particularly the ISO…

Q: If a spline is transmitting 2,000 lb-in torque, what would be the major spline diameter for a 4A…

A:

Q: M25x6-4h5h-23   describe each part

A:

Metrology of Screw Threads

Screw threads are a series of ridges having the profile of a helix. This helix profile runs continuously along the length of a uniform solid or a hollow bar of a circular cross-section at periodic intervals. These helix ridges are also formed over a conical bar. These continuous helical ridges are termed threads.