What is the function of the DC motorarmatureChoose one answer:a. Performs the function of force-moment conversion of electric currentenergy into mechanical energyb. Performs the function of force-moment conversion of mechanicalenergy into electrical energyc. Magnetic flux functiond. Motor support function In the T-shaped equivalent circuit of the transformer for the load mode, indicate the resistance in which power will bereleased, equal to the electrical losses of the secondary winding.Select one:O a. 12O b.11O c. ZloadO d. l2O e. ImClear my choiceWhich of the listed quantities determines on the substitution circuit the resistance of the magnetization branch RmSelect one:O a. Dol, Do2O b. Pel - electrical lossesO C. Pst - losses in steelO d. K-transformation ratioO e. om - mutual induction flowClear my choice

According to guidelines we need to solve only the first question. According to the question we have…

What is the function of the DC motor armature Choose one answer: a. Performs the function of force- moment conversion of electric current energy into mechanical energy b. Performs the function of force- moment conversion of mechanical energy into electrical energy c. Magnetic flux function d. Motor support function

What is the function of the DC motor armature Choose one answer: a. Performs the function of force- moment conversion of electric current energy into mechanical energy b. Performs the function of force- moment conversion of mechanical energy into electrical energy c. Magnetic flux function d. Motor support function

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.9P

See similar textbooks

Similar questions

For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
Consider an ideal transformer with N1=3000andN2=1000 turns. Let winding 1 be connected to a source whose voltage is e1(t)=100(1| t |)volts for 1t1ande1(t)=0 for | t |1 second. A2- farad capacitor is connected across winding 2. Sketch e1(t),e2(t),i1(t),andi2(t) versus time t.
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
Answer only please The resistance of a transformer winding is 0.25 ohm at 25oC. When operating at full load, the temperature of the winding is 75oC. The temperature coefficient of resistance for copper at 0oC is 0.00427 per oC. What is the winding resistance at full load? a. 0.512 ohm b. 0.315 ohm c. 0.298 ohm d. 0.271 ohm
eeff
A three-winding transformer is connected to an AC voltage source as shown in the figure. The number of turns is as follows: N₁ = 100, N₂ = 50, N3 = 50. If the magnetizing current is neglected, and the currents in two windings on secondary side are 2230° and 22150°, then what is the value of the primary current in Ampere? I 0000000000- N₁ № ₂ Z 00000 00000 Z N3 H I₁₂ I₁₂₁ ¹3
A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
The core of a transformer operating at 50 Hz has an eddy current loss of 100 W/m3 and the corelaminations have a thickness of 0.50 mm. The core is redesigned so as to operate with the same eddycurrent loss but at a different voltage and at a frequency of 250 Hz. Assuming that at the new voltage themaximum flux density is one-third of its original value and the resistivity of the core remains unaltered,determine the necessary new thickness of the laminations. Clear and detailed solution.
I need the answer quickly
oopp
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
opper losses Which of following is a variable loss in a transformer? O Constant loss O Eddy current Hysteresis losses O Copper loss