Q choose the correct answer: 1-Brushless excitation system consisting of.... a- Stator field winding and power diodes b-stator and rotor field winding and capacitor c- stator and rotor field winding and capacitor d- Everything mentioned in the options 2- Voltage generated per phase in an alternator is proportional to a-Flux per pole b-Number of turns in armature c- Winding factors d- Everything mentioned in the options e- Frequency of waveform 3- If input mech. Power of SG constant, the functionality of AVR is a- Control flux of rotor b-Control terminal voltage c- Control flux and terminal voltage d-Control Load angle

Q choose the correct answer: 1-Brushless excitation system consisting of.... a- Stator field winding and power diodes b-stator and rotor field winding and capacitor c- stator and rotor field winding and capacitor d- Everything mentioned in the options 2- Voltage generated per phase in an alternator is proportional to a-Flux per pole b-Number of turns in armature c- Winding factors d- Everything mentioned in the options e- Frequency of waveform 3- If input mech. Power of SG constant, the functionality of AVR is a- Control flux of rotor b-Control terminal voltage c- Control flux and terminal voltage d-Control Load angle

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: For operation at 60 Hz and a given peak flux density, the core loss of a given core is 1W due to…

Q: 4. A three-phase A-connected six-pole winding is installed in 36 slots on a stator. There are 150…

A: Introduction A three-phase delta-connected system is a type of electrical power distribution…

Q: In a transformer setup, two coils with a magnetic core between them, a changing magnetic field…

A: A transformer is a static electric device consisting of two or more electric circuits interlinked by…

Q: An iron core is most often used in an AC transformer to 1.provide a better coupling between the…

A: An AC transformer is a device used to transfer electrical energy between two or more circuits…

Q: 1. In a transformer, which options are correct: A. Works on Faraday’ law and Ampere’s law B. DC…

Q: The armature of a shunt generator has 0.08-ohm effective resistance. Each brush has an effective…

A: In a shunt generator is having, Armature resistance, Ra=0.08 Ω. Resistance of each brush, Rb=0.02 Ω…

Q: 4. In a transformer, which options are correct: A. Works on Faraday' law and Ampere's law B. DC…

A: Transformer is a static device the transfer electrical energy from one electrical circuit to another…

Q: (Q1f, Draw and compare the per-phase electrical equivalent circuits of a transformer and of an…

A: To draw and compare the per-phase electrical equivalent circuits of a transformer and of an…

Concept explainers

Winding and Constructions

Alternating Current (AC) winding is generally of the 3-phase type due to the inherent advantages of the 3-phase machine. Armature coils must be connected to the yield balance (equivalent in magnitude and 2/3 of the series phase difference of the rod) 3-phase electromotive forces (emf). The armature should be divided into step-bands to start with slots around the perimeter.In the construction of AC machines, the frame is used as an external protective shield to protect it from environmental conditions. The frame also serves as the outer perimeter, allowing the interior to be easily placed. The static state section of the devices is the stator winding attached stator.

Question

Q choose the correct answer:
1-Brushless excitation system consisting of....
a- Stator field winding and power diodes
b-stator and rotor field winding and capacitor
c- stator and rotor field winding and capacitor
d- Everything mentioned in the options
2- Voltage generated per phase in an alternator is
proportional to
a- Flux per pole
b- Number of turns in armature
c-Winding factors
d- Everything mentioned in the options
e- Frequency of waveform
3- If input mech. Power of SG constant, the functionality of
AVR is
a- Control flux of rotor
b-Control terminal voltage
c- Control flux and terminal voltage
d-Control Load angle

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Winding and Construction of the Rotor and Stator

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A d.c. series motor is running whith a speed of 800 r.p.m. while taking a current of 20 A from the supply. If the load is changed such that the current deawn by the motor is increased to 50 A , calculate the speed of the motor on new load . The armature and series field winding resistances are 0.2 ohm and 0.3 ohm respectively . Assume the flux produced is proportional to the current . Assume supply voltage as 250 V
A single phase 60 Hz transformer has its core volume of 1.5x10-3 cu m. The maximum flux density is 1.0 tesla and the hysteresis constant of the core is 6000. find the hysteresis loss.
3-4. A three-phase, Y-connected, four-pole winding is installed in 24 slots on a stator. There are 40 turns of wire in each slot of the windings. All coils in cach phase are connected in series. The flux per pole in the machine is 0.060 Wb, and the speed of rotation of the magnetic field is 1800 r/min. (a) What is the frequency of the voltage produced in this winding? (b) What are the resulting phase and terminal voltages of this stator? 3-5. A three-phase, A-connected, six-pole winding is installed in 36 slots on a stator. There are 150 turns of wire in each slot of the windings. All coils in each phase are connected in series. The flux per pole in the machine is 0.060 Wb, and the speed of rolation of the magnetic fieid is 1000 r/min. (a) What is the frequency of the voltage produced in this winding? (b) What are the resulting phase and terminal voltages of this sStator?
Describe the figures below and how each of figure below are working
3-5. A three-phase, A-connected, six-pole winding is installed in 36 slots on a stator. There are 150 turns of wire in each slot of the windings. All coils in cach phase are connected in series. The flux per pole in the machine is 0.060 Wb, and the speed of rolation of the magnetic field is 1000 r/min. (a) What is the frequency of the voltage produced in this winding? (b) What are the resulting phase and terminal voltages of this stator? 3-6. Athree-phase, Y-connected, 60 Hz, two-pole synchronous machine has a stator with 5000 rurns of wire per phase. What rotor flux would be required to produce a termi- nal (line-to-line) voltage of 13.2 kV? 3-7. Modify the MATLAB in Example 3–1 by swapping the currents flowing in any two
(a) Using Faraday's Law as a starting point prove that the maximum operating voltage of a transformer to avoid magnetic saturation is given by the following equation: Q3 Vrms=4.44N.f.Bmax.Ac where: Vrms = maximum rms operating voltage avoiding magnetic saturation N = number of turns in the winding f= electrical frequency (Hz) Bmax = maximum flux density (T) (typically 1.3T for iron) Ac = Iron core cross sectional area (m²) A single phase transformer has the parameters shown on Table Q3 and is connected to a 230 V and 50 Hz AC supply. Sketch the equivalent circuit and using this determine: (b) (i) The Secondary voltage under Open Circuit (Vsoc) (ii) The Secondary voltage, current and power (W) given a 0.6 Q resistive Load. (iii) The efficiency and voltage regulation at this load Through suitable calculations determine whether the size, weight or cost of this transformer could be reduced such that it operated below a maximum flux density of 1.3 T and the current density in both windings…
A dc shunt generator delivers 50 kw at 250 v, its armature has a 4-pole wave winding with a resistance of 0.01 ohm and its field resistance is 125 ohm. if the number of turns in the armature is 201 and the flux per pole is 0.02 wb, find the voltage generated and the speed of operation. *
A. The brushes used in a DC generator a) ride against the commutator segments. b) are made from material softer than the commutator segments. c) are generally marked Al and A2 d) all of the above B. A magneto is a DC generator that uses for its pole pieces. a) electromagnets b) permanent magnets c) either "a" or "b" d) neither "a" nor "b"
Is this armature winding a progressive or a retro-progressive winding? W N Select one: 2 B 4' O a. Both O b. Progressive OC. Neither O d. Retro-progressive B S
9. How does the concept of magnetic saturation impact the performance of transformers and inductors?
A lap-winding DC machine has 24 coils, 18 turns per coil, and 4 poles. The average flux density per pole is 1T. The effective length is 40 cm and the armature radius is 10 cm. The armature velocity is 140.2 rad/sec and the armature current is 24 A. The average flux per pole in Wb is: 6.283 0.06283 O 0.6283 0.006283
There are 175 slots in a 3-phase, 16-pole, 50 Hz., star connected alternator. There are 4 conductors in each slot and all the conductors in a phase are connected in series. Coil span is 130° electrical and the flux per pole is 0.04 Weber sinusoidallly distributed. Calculate the emf induced per phase.