A three-winding transformer is connected to an AC voltage source as shown in the figure. The number of turns is as follows: N₁ = 100, N₂ = 50, N3 = 50. If the magnetizing current is neglected, and the currents in two windings on secondary side are 2230° and 22150°, then what is the value of the primary current in Ampere? I₁ N₂ 0000000000 N₁ eeeee reeeee z N3 I₁ I₂

A three-winding transformer is connected to an AC voltage source as shown in the figure. The number of turns is as follows: N₁ = 100, N₂ = 50, N3 = 50. If the magnetizing current is neglected, and the currents in two windings on secondary side are 2230° and 22150°, then what is the value of the primary current in Ampere? I₁ N₂ 0000000000 N₁ eeeee reeeee z N3 I₁ I₂

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

14. The maximum flux of a 50H2 transformer is 0.001Wb. If the primary is wound Vwith 1080 turns, find the applied primary voltage and then calculate the number of turns required for a 15V secondary. Ans: N2=67
Assume 120Vrms is applied to the transformer primary (from P1 to P2). What is the expected secondary voltage measured from S1 to S2? 4:1 Np = 320 Ns = 80 S2 P20 80 Vrms 15 Vrms 30 Vrms 60 Vrms
opper losses Which of following is a variable loss in a transformer? O Constant loss O Eddy current Hysteresis losses O Copper loss
Which of the following is the correct equation for calculating the rated current for a single-phase transformer? A. I=va/e b.I=sc/e c.a/e d.e×z/e
How does the coupling factor affect the primary and secondary voltages? For example if the turns ratio in my transformer is 1:2 and the Vin is 10V, the voltage on the primary side is 10V and the voltage on the secondary side is 20V when the coupling factor (k) is 1. What will the primary and secondary voltages be if the coupling factor becomes 0.5?
6. For the air core transformer circuit shown below, determine the currents la and lb in the direction shown. Express each answer in polar form. R1-302 www la ZI1=150 E=10/0 M=j20 Ze= n Z12=j62 lb R2=50 la Ib
A 200 V/100 V, 50 Hz transformer is to be excited at 40 Hz from 100 V side. For the exciting current to be constant, the applied voltage should be ?
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diodeshave? (Use constant voltage drop model for the Silicon diode) D IN4001 OV 10 kN IN4001 DELL
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.
Which of the following statements is true about an ideal transformer? O It changes the magnitude of DC signals. O It converts DC signals into AC signals. O It converts AC signals into DC signals. O It changes the magnitude of AC signals. hp
7. A coil having a resistance of 20 ohms and an inductance of 0.75 henry is connected in series with a 30-ohm resistor and to a 120-volt d-c source. A switch across the series resistor is then closed, and the circuit is assumed to be in a steady-state condition. At the instant the switch is opened, what will be the rate of current change and the power delivered by the magnetic field.