Well HydraulicsA circular dug well in fine sand region has a yield of 15 l/s under a depression head of 4 m.Assuming specific capacity per unit area as 0.8/h, the bottom diameter of the dug well is

A circular dug well in fine sand region- Yield Q=15 l/s Depression head S=4 m, Specific capacity per…

Answered: Well Hydraulics A circular dug well in…

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter8: Seepage

Section: Chapter Questions

Problem 8.11P

See similar textbooks

Similar questions

Refer to Figure 7.24. The following data were collected during the field permeability measurement of a confined aquifer using a pumping test. Determine the hydraulic conductivity of the permeable layer. Use Eq. (7.49). Thickness of the aquifer, H = 4.5 m Piezometric level and radial distance of the first observation well: h1 = 2.9 m; r1 = 17.8 m Piezometric level and radial distance of the second observation well: h2 = 1.8 m; r2 = 8.1 m Rate of discharge from pumping, q = 0.5 m3/min
For the drilled shaft described in Problem 19.7, estimate the total elastic settlement at working load. Use Eqs. (18.45), (18.47), and (18.48). Assume that Ep = 20 106 kN/m2, s = 0.3, Es = 12 103 kN/m2, = 0.65 and Cp = 0.03. Assume 80% mobilization of skin resistance at working load. (See Part c of Problem 19.7) 19.7 Figure 19.16 shows a drilled shaft without a bell. Here, L1 = 6 m, L2 = 7 m, Ds = 1.5 m, cu(1) = 50 kN/m2, and cu(2) = 75 kN/m2. Find these values: a. The net ultimate point bearing capacity. Use Eqs. (19.23) and (19.24) b. The ultimate skin resistance. Use Eqs. (19.26) and (19.28) c. The working load, Qw (FS = 3) FIG. 19.16
For the drilled shaft described in Problem 19.7, determine these values: a. The ultimate load-carrying capacity b. The load-carrying capacity for a settlement of 25 mm Use the procedure outlined in Section 19.8. 19.7 Figure 19.16 shows a drilled shaft without a bell. Here, L1 = 6 m, L2 = 7 m, Ds = 1.5 m, cu(1) = 50 kN/m2, and cu(2) = 75 kN/m2. Find these values: a. The net ultimate point bearing capacity. Use Eqs. (19.23) and (19.24) b. The ultimate skin resistance. Use Eqs. (19.26) and (19.28) c. The working load, Qw (FS = 3) FIG. 19.16

Recommended textbooks for you

Principles of Geotechnical Engineering (MindTap C…

Civil Engineering

ISBN:

9781305970939

Author:

Braja M. Das, Khaled Sobhan

Publisher:

Cengage Learning

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781305081550

Author:

Braja M. Das

Publisher:

Cengage Learning

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Principles of Geotechnical Engineering (MindTap C…

Civil Engineering

ISBN:

9781305970939

Author:

Braja M. Das, Khaled Sobhan

Publisher:

Cengage Learning

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781305081550

Author:

Braja M. Das

Publisher:

Cengage Learning

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Geotechnical Engineering (MindTap…

Civil Engineering

ISBN:

9781305635180

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Well Hydraulics A circular dug well in fine sand region has a yield of 15 l/s under a depression head of 4 m. Assuming specific capacity per unit area as 0.8/h, the bottom diameter of the dug well is