WEIGHTED MEASUREMENTS. A distance AB is measured five times as 610.03, 610.01, 610.05, 610.04, and 610.02 meters. The three measurements were given weights of 3, .2, 1, 2, and 3 respectively, by the head tapeman. Determine the weighted mean for distance AB. Also, determine what difference results if later judgement revises the weights to 2, 3, 1, 3 and 2.

WEIGHTED MEASUREMENTS. A distance AB is measured five times as 610.03, 610.01, 610.05, 610.04, and 610.02 meters. The three measurements were given weights of 3, .2, 1, 2, and 3 respectively, by the head tapeman. Determine the weighted mean for distance AB. Also, determine what difference results if later judgement revises the weights to 2, 3, 1, 3 and 2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

show complete solution and box the final answer
i need the answer quickly
II. Theory of Errors 1. The distance from their home to their school has five measurements. The table below are the measured lengths and weights. Compute the most probable value of the measurement. Measured Length 216.13 210.14 213.17 215.19 211.11 Weight 1 2 3 4 5
*PLEASE WRITE THE SOLUTION *THE ANSWERS MUST BE IN 4TH DECIMAL PLACE *Need in 30mins at most 1hr...
can u help Write a brief conclusion on the answer that you obtain from the above question. Is it liable and okay to obtain this amount of error? Explain your point of view.
FOUR DECIMALS PLACES: PLEASE 100%
A steel tape standardized at 20degree celcius and supported through out under tension of 90N Was found to be 30.377m long. The tape had a cross sectional area of 55mm^2 and a weight of 73g/m. This tape was used supported at the ends only with a constant tension of 78N to measure a line from A to B in nine segments. The data given in the following table were recorded. Apply correction for tape, length,temperature,pull,sag and tape not horizontal to determine the correct length of the line Difference in Elevation Cm) 0-392 Section Meacured Recarded Distance) Tempergrare A-1 15 1- 2 30 15 0.301 2-3 30 16 O.191 3-4 16 0-255 4-5 30 16 0-38 5-6 30 8.636 6-7 0.782 7-6 30 0-825 8-8 25.348 18 0.578 Sum = 265-348 m
In (Figure 1), F = {80i + 96j + 48k} lb. Figure 1 ft -2 ft 3 ft 45° B 1 of 1 Part A Determine the magnitude of the moment of F about point A. Express your answer in pound-feet to three significant figures. 15] ΑΣΦ11 MA = Submit Part B α, B, y = Submit Request Answer Provide Feedback Determine the coordinate direction angles of the moment of F about point A. Express your answers in degrees to three significant figures separated by commas. vec U/ ΨΕ ΑΣΦ ↓↑ vec Request Answer ? lb. ft ? Next >
Determine the deflection @C using Moment Area Method. (Your final answer should be in "mm") 10 kN/m 4 kN A C D B 7 т 3 т 4 т E = 200 GPa I = 140 x 106 mm* Note: Express your answer in two decimal places. No need to type the units.
2. The surveying professor require his student to measure line CD by pacing. In order for the student to provide an accurate length of line CD, he must know his pace factor. The student measured line AB , 45 meters long and walked through for several trials. The following numbers of steps or paces on line AB and CD are tabulated below. On line AB Trial Counted paces 1 72.50 2 72 71 4 72 71.5 On line CD Trial Counted paces 1 285 2 283 284.5 4 282 283.5 Determine the paced distance of line CD b. Determine the Relative Precision of а. measurement if the taped distance of line CD is 178.05 m. LO
Determine the deflection @Cusing Moment Area Method. (Your final answer should be in "mm") 8 kN/m 3 kN A C D 6 т 4 m 3 т E = 200 GPa I = 260 x 106 mm4 %D
A particle which moves with curvilinear motion has coordinates in millimeters which vary with the time t in seconds according to x = 5.5t² - 2.0t and y = 6.5t² - 3/2.4. Determine the magnitudes of the velocity v and acceleration a and the angles which these vectors make with the x-axis when t = 5.1 s. Answers: When t = 5.1 s, V = a= i i mm/s, ex- i mm/s², 0x = i