the measurement of the base and altitude of a triangle are found to be 40 and 56 cm, respectively. the possible error in each measurement is 0.25cm. Use differentials to approximate the possible propagated error in computing the are of the triangle. (round your answer to two decimal places.) Show your full solution.

Q: A car is traveling at speed v when the brakes are suddenly applied, causing a constant deceleration…

A: Hello dear this is the solution of your problem The answer is found to be Distance travelled by car…

Q: 0 = 0.15t² → Eq. (1) ; r = 0.9 -0.121² → Eq. (

A: (-0.449 er + 0.270 e?) m/s or 0.52 m/s

Q: 8 kip 8 kip A В D - 5 ft 5 ft- +5 ft -5 ft

A: According to given data  since load is symmetrical  Ra=RB=8 kip

Q: The velocity potential function is given by o = 5 (x – y'). Calculate the velocity components at the…

A: Following is the given velocity potential function:

Q: Determine the moment of inertia ly (in.4) of the shaded area about the y-axis. Given: x = 4 in. y =…

A:

Q: Solve for: a) velocity of B (m/s) b) angular velocity of AB (rad/s) B 500 mm A

A:

Q: 3. Determine the slope and vertical displacement of point A on the beam shown in the accompanying…

A:

Q: A Pelton turbine is a turbine working under atmospheric pressure and which rotates thanks to water…

A: Given datavelocity of turbine blade moves =wwater travels with velocity=vwater flow diameter=dwater…

Q: uate the position, velocity and acceleration when t = 3 seconds.

A:

Q: INSTRUCTION: Answer the problem set given. Provide a complete and clear solutions with appropriate…

A: Given A cantilever beam  Required  Maximum deflection using double integration method

Q: Fixed Point Iteration Solve the system of nonlinear equations using Fixed Point Iteration approach.…

A: Given: y=-x2+x+0.75y+5xy=x2

Q: Determine the moment of inertia ly (in.“) of the shaded area about the y-axis. Given: x = 5 in. y =…

A:

Q: The rotation of the 0.9-m arm OA about O is defined by the relation Eq. (1), where θ is expressed in…

A:

Q: Figure P 12.2. Estimate the ultimate point load or tip resistance Q, by each of the following 4…

A:

Q: A 20 m long concrete pile with a rectangular cross section of 460 mm × 460 mm fully embedded in sand…

A:

Q: A 443-lb block is resting on a rough horizontal surface for which the coefficient of friction is…

A: Given data Weight of Block Equal to 443 LB Coefficient of friction is equal to 0.4 We are asked to…

Q: I need detailed explanation to solve the exercise below. There are some formulas and hints, I also…

A: L = 20 m B = 460mm

Q: solve accurately with steps

A: Answer- I have given hand written step by step solution in the explanation box. Explanation:Step…

Q: Show the complete solution and the necessary graphs/diagrams. Use 2 decimal places in the final…

A: Given: Parametric equations of particle movement: x=3t2-1y=t3-3t2+t-3 Angular velocity at t seconds…

Q: Interpolate between In (4) = 1.386294361 and In (8) = 2.079441542. Also, compute the percent…

A: Given  Ln(4) =1.386294361  Ln(8) = 2.079441542

Q: 1. The angular displacement of the robotic arm of Figure 1 is programmed according to the…

A:

Q: The ball at A is kicked with a speed of (24 +0.01) m/s at an angle e = (25 +0.1)°. Determine the…

A:

Q: Consider H.W.4 a closed rectangular box with a squar base. If base side is measured with evror at…

A:

Q: - A water tank has the shape of a spherical segment volume of the tank can be computed from the…

A:

Q: Use the virtual work method to determine the horizontal and vertical displacement of joint E. Show…

A:

Q: A

A:

Q: 1. Determine the value of M1 if the system shown is equivalent to a single force acting at point C.…

A: Given Data:X=1Y=6Z=01X in:11in2Y in :26in8X kips:81 kips1YZ kips:160 kips

Q: In the given figure below, a tube was supported at A and E with a ball and socket and a wire at D…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: The curvilinear motion of a particle is defined by vx=50-18t and y=100-4t2, where vx is in m/s, y is…

A:

Q: A 20 m long concrete pile with a rectangular cross section of 460 mm x 460 mm fully embedded in sand…

A:

Q: Pitot tube is an instrument that is used to measure flowrate in a pipe. Figure 3 shows water flowing…

A:

Q: A 20 m long concrete pile with a rectangular cross section of 460 mm × 460 mm fully embedded in sand…

A:

Q: What is the period of this sine-function?

A: periodic function:

Q: For the shape below, assume the following dimensions: a = 175 mm b = 220 mm d = 300 mm t = 23 mm The…

A: Given:Required :Moment of inertia along centroidal y axis

Q: LA curvilinear path is given as e x² + y³ /27 = 27 . A particle is moving on this path at a constant…

A: Solution: Given data: Particle moving at constant speed of 8 m/s

Q: V Figure 3

A:

Q: A 20 m long concrete pile with a rectangular cross section of 460 mm x 460 mm fully embedded in sand…

A: Already some formulae given , Here for terzaghi equation, a few more are needed1) for loose sand , K…

Q: The acceleration of a particle is given by a = 4t - 38, where a is in meters per second squared and…

A: Equation of the acceleration = a = 4t - 38 At t = 0, s0 = 8m and v0 = 2ms     To find -…

Q: In the diagram below, the magnitude of vector A is 19 N, and the magnitude of vector B is 13 N and…

A: ASKED: To determine the magnitude and direction of the resultant vector.   Magnitude of vector A |A|…

Q: Determine the moment of inertia ly (in.“) of the shaded area about the y-axis. Given: x = 4 in. y =…

A: To Find :- moment of inertia Iy of shaded portion about Y- axis.

Q: A moving particle has a velocity described in the following data: 15 Time (sec) Velocity (m/s) 24 0…

A:

Errors in surveying

An error in surveying is defined as the difference between two or more values of an identical quantity. However, the estimates are never accurate and there will always be a degree of variability regardless of the research tool or method used. These differences are known as errors that need to be reduced or eliminated to maintain certain levels of accuracy. Even if you carefully follow the prescribed test procedures, the considerations may contain errors.