Water is flowing through a venturimeter shown. The difference in pressure between Point 1 (D = 4cm) and Point 2 (D = 2cm) is measured using open tubes. If h is 50cm, solve the velocity head at Point 1. 下 1 O 0.034m O 0.208m O 0.085m O 0 039m

Water is flowing through a venturimeter shown. The difference in pressure between Point 1 (D = 4cm) and Point 2 (D = 2cm) is measured using open tubes. If h is 50cm, solve the velocity head at Point 1. 下 1 O 0.034m O 0.208m O 0.085m O 0 039m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The circular stream of water from a faucet is observed to taper from a diameter of 20 mm to 10 mm in…

Q: A small turbine is run by water from a reservoir, as shown. Both the pipe leading to and away from…

A: Given data: Diameter of the pipe, D= 0.6 ft Velocity, V=10 ftsec The volume flow rate from the…

Q: 4-9. The velocity profile of a liquid flowing through the pipe is approximated by the truncated…

A: Specific weight of water, Velocity, To find: Mass flow.

Q: A tank system is shown in the sketch. The temperature is 20 Celsius . The tank system contains water…

Q: Water flows from the inlet at point 1 to outlet at point 2 at 0.19 N/s. Assuming steady flow, and…

Q: Q.88. A horizontal venturimeter with inlet diameter 200 mm and throat diameter 100 mm is used to…

Q: 12.7 The radial component of velocity of water leaving the cen- rifugal pump sketched in Fig. P12.7…

A: Given data:V2=90 ft/sVr2=45 ft/sN=3000 rpm

Q: liquid d=0.7 water 260 mm %3D 1.0 m

Q: aState the three types of flow and explain them.

A: Answer:- Types of fluid flow:- The classification of fluid flow according to their fluidity is…

Q: Question-03: Water flows downward along a pipe (shown in fig) that is inclined at 30'. A…

A: Draw the setup of the manometer

Q: (Bernoulli/continuity) Water flows into a large tank at a rate of 0.012 m³/s as shown in the figure…

A: Answer We are given water flow rate Q = 0.012 m3/s number of holes at bottom = 20 diameter of each…

Q: Q2) Water flows through a vertical contraction (venturi) section. Piezometers are attached to the…

Q: Current Attempt in Progress (Bernoulli/continuity) Water flows steadily through a diverging tube as…

A: Given:in fig Diverging tube d3=1.03ft d2 =0.74 d1=0.52ft Specific gravity of manometric tube…

Q: A cylindrical tank with a constant depth h is being filled with water by Pipes 1 and 3. An outlet is…

Q: oil (SG = 0.88) dischargesfrom a pipe (D = 13 in.) through a sharp-crested, round orifice (diameter…

Q: Flowing water in pipe 1 and pipe 2 is flowing to pipe 3 which is 7m long and discharges the water to…

A: We have to determine the value of h as per the given data like diameters of pipes and velocity of…

Q: E o m Fluid A Fluid B 20 cm 60 cm

Q: ion probe at station 2 and a static pressure tap on 1. The velocity at station 2 is 2 times that at…

A: Given:- Air with density=1.2kg/m3 deflection=5cm To find:- velocity at station 2

Q: Current Attempt in Progress (Bernoulli/continuity) Water flows steadily through a diverging tube as…

Q: A closed tank containing water is partly filled with water and the air space above it is under…

A: Given- Diameter of the bore=5 cm, Friction loss=1.5 m of water, Discharge Q=15 L/s, Density of…

Q: Water flows through the pipe contraction as shown in the figure. The drop in the piezometer level…

A: According to given data Water flows through the pipe contraction The drop in the piezometer level…

Q: Please include free body diagram The head of water over an orifice of diameter 100 mm is 5 m. The…

Q: SITUATION 9: Medium oil having a sp. gr. of 0.90 flows through a 120 mm diameter pipe with a mean…

A: Diameter of pipe, d = 120mmMean velocity, Vav = 5.3m/secThe specific gravity of the soil, G =…

Q: View Policies Current Attempt in Progress (Bernoulli/continuity) Water flows steadily through a…

Q: The height of water above the 5 mm diameter orifice stands 180 mm. What is the theoretical velocity…

Q: V. water 0-8 m immiscible liquid of sp. gr. 1-6 1 m What is the gauge pressure at pointP in the…

Q: A horizontal venturimeter with inlet and throat area as 706.858 cm2 and 176.715 cm2 respectively is…

A: We have to determine the value of rate of flow of the horizontal venturimeter with inlet and troat…

Q: A cylindrical tank with depth h and radius 1.72m is being filled with water by Pipes 1 and 3. An…

Q: Q20) For the steady flow of gas in the conduit shown, what is the mean velocity at section 2? Answer…

Q: Find the hydraulic mean depth of a pipe of diameter 200 mm when the rate of flow of water through…

A: Given: Diameter, d = 200 mm = 0.2 m Discharge, Q = 200 lt/s Assuming that the pipe is running…

Q: 500N 1000N 30 2000N (a)

Q: 2-) A footbal player wants to throw the ball into the hole which is behind the wall. If she can kick…

A: Applying projectile motion equations formulas to be used, R=vo2sin2θog…

Q: Suppose the impeller in the preceding question supplies 10 kW of water power and is placed in a tank…

A: Objective: To determine the velocity gradient (G). Given: Power supplied to the tank (P) = 10 kW…

Q: Q3) The pressure outside the droplet of water of diameter (0.04 mm) is (10.32 N/cm²) atmospheric…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

Water is flowing through a venturimeter shown. The difference in pressure between Point 1 (D = 4cm) and Point 2 (D = 2cm) is
measured using open tubes. If h is 50cm, solve the velocity head at Point 1.
下
1
O 0.034m
O 0.208m
O 0.085m
O 0.039m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Concept

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

SITUATION 8: A 180 kN force is supported by a vertical jet of water thru a nozzle. The velocity of the water is 15.4 m/s and the diameter of the jet is 2.2 cm. 36. Compute for the discharge of water from the jet. a. 0.04346 b. 0.00859 c. 0.00589 d. 0.00585 37. What is the velocity of the water before it reaches the maximum height? EVIE m a. 17.96т b. 30.77 m m c. 23.28- d. 3.436 38. What is the maximum height? a. 31.21 m c. 36.17 m b. 27.62 m d. 23.81 m
2. Determine the magnitude and direction of the force exerted by a fluid with s.g. of 0.84 on the double nozzle shown. When V1=10 m/s and Vz=13 m/s. The axes of the pipes and both nozzles all lie in horizontal plane. Neglect friction. 125 mm 250 mm 100 mm
Draw a V and M diagram of the system below using the function method.
How can I find the solution for the pressure at point B only? (answer is given)
q5
. The head of water over an orifice of diameter 100 mm is 10 m. The water coming out from the orifice is collected in a circular tank of diameter 1,5 m. The rise of water level in this tank is 1.0m in 25 seconds. Also the coordinates of a point on the jet, measured from vena contracta are 4.30 m horizontal and 0.50 m vertical. Find the device coefficients.
e)/ An open rectangular tank (8m) long, (3m) wide and (2m) deep is filled water to depth (1m), the tank is accelerated horizontally with constant value of ( 2 m/sec²), determine: 1- The angle of water surface. 2- The volume of water displacement because the acceleration.
Fast.
An open tank filled with water and pulled at inclined surface as shown. Compute the acceleration which keeps the water surface at the position shown in fig. compute pressure at point(A) before and after acceleration. az ax 1.0m 1.40m A Static surface 3 Accelerated surface
سنب Fluid mechanics
E8