In the conical tank shown below, water exits through the spout at the top. Assume the tank is full of water. Determine the work required to pump ½ of the water out of the tank. The density of water is 1000 kg/m3. The spout is at a height 1 m above the top of the tank. The radius of the tank is 6 m and the height of the tank is 14m.

Q: Two reservoirs A and B have elevations of 250 m and 100 m, respectively. The two tanks are connected…

A:

Q: Determine the pressure head at point 1 and point 2 (in meters). Also, determine the power delivered…

A:

Q: power output of the motor?

A:

Q: A reservoir is filled with 4 m of water. A pump of area 0.009 m² at the bottom of the reservoir is…

A: ###Determination of flow rate Q through pump ##

Q: Determine the value of hin meters indicated in the

A:

Q: Calculate the pressure in the pipe (Point A). The area of the reservoir is 100 times the area of the…

A:

Q: 6. A water is supplied through the pipe network system as shown below. The reservoir water level…

A:

Q: Find the time it takes to decrease the water level in the tank 1 by 1.5m. Use C = 0.60 h.l. 2.3m do:…

A: Given data: diameter of tank 1 D1=6m Dimensions of tank 2 are 3m x 2m Difference in water level h=…

Q: Question: The rainwater discharge system in the figure with a width of b=1 m perpendicular to the…

A: Solution

Q: A pipe discharges 130 lps of water into a reservoir at a point 1.85 m below the water surface. At…

A:

Q: C) In a cylinder-piston arrangement shown (D₁ = 100 mm), the piston is moving downwards at Vp = 0.5…

A: step 1-

Q: A liquid (SG = 0.920) is being pumped from a reservoir as shown. The pressures at point %3D 1 and 2…

A:

Q: Q3: A: In figure (3), the flow rate of water from reservoir (A) is 0.438 m³/s. Determine the power…

A: ZA = 123m  ZB = 122m ZE  = 80m  C = (8g/f)0.5  or, f = 8g/C2 = 8*9.81/1202 = 0.0055  V1 = Q/A1 =

Q: The large tanks A and B are connected by a variable section pipe. The water level in tank A is 2m,…

A:

Q: Three pipes are connected in series. Pipe 1 has length of 850m and diameter of 600mm. Pipe 2 has…

A:

Q: a cylindrical vessel has 0.5m diameter and 1m height rotates at 10rad/s. initial height of Mercury…

A:

Q: Energy Equation The diameter from point B to the pump is 3 inches and the diameter from the pump to…

A: To find pressure at point B

Q: H.W(2):Water flows steadily from a large tank through a pipe that splits into two smaller pipes as…

A: Given data in question  Water Depths Diameter  To find out  Pressure at point 1 Discharge through…

Q: 4. The water discharge through the 200 mm pipe shown is throttled to a velocity of 2.4 m/s by means…

A: delivery pipe diameter= 200 mmsuction pipe diameter = 300mlength of suction pipe = 30 mvelocity =…

Q: Two reservoirs are connected by distribution pipeline as shown in the figure. Assuming no head loss…

A:

Q: With the chamber-pipe system in the figure, the ideal fluid (water) taken from the infinitely sized…

A: Given:- The chamber-pipe system is given  The fixed diameter of BCDEF pipe = 40 cm  The elevation of…

Q: In the situation shown in the figure, the water flows from the upper tank A to the lower one tank B.…

A: Answer Apply Bernoulli's equation at point A and B PAγ+VA2γ+zA = PBγ+VB2γ+zB+hL PA and PB are…

Q: 14. Water is pumped from one tank to another through a 0.100 m smooth plastic tube. The flow rate is…

A:

Q: 1. An orifice at the bottom of a rectangular tank has a cross-sectional area of 0.004m². The tank…

A:

Q: Water is pumped from reservoir A at elevation 250 m. The pump is close to reservoir A and is at the…

A:

Q: Provide complete solution.  A frustum of a cone is shown, with the orifice at the bottom. C_d=0.62.…

A:

Q: Question: Water is flowing in the vertical pipe system shown in the figure. Water exits to the…

A: The given figure is shown below:

Q: Bernoulli. Water is siphoned from a large tank filled to a depth of 3m using a tube (Dr=0.6 cm) with…

A: Bernoulli's theorem : In fluid dynamics, Bernoulli's theorem describes the relationship between…

Q: Water flows from a to e through the pipe system shown in the figure. It is known that the flow in…

A:

Q: 5. Oil (S=0.92) is transported through the system as shown below. If the pressure head difference…

A: Given :

Q: A cylindrical tank, filled with water and axis vertical, is open at one end and closed at the other…

A:

Q: Water 6 m F₂ Figure la F₁ 2 m Gate m

A:

Q: storage tank located  30m above the pump.  The suction pipe is 350mm in diameter and 12m in length,…

A:

Q: Problem 4. Fundamentals of Fluid Flow. Solve for the head added due to pump (in meters) for the…

A:

Q: B: A closed cylindrical tank filled with water has a hemispherical dome and is connected to an…

A: Asked: To determine the pressure in pipe B and the pressure head, in millimeters of mercury, at…

Q: Situation 7: Water is pumped from reservoir A at elevation 750.0 ft to reservoir E at elevation 800…

A:

Q: Bernoulli's theorem demonstration: D ° ° 1° d 5 L of Water is flowing through a venturimeter in…

A: D = 32 mm =0.032 md = 23 mm = 0.023 mArea, of diameter D = 0.023 mArea, of diameter d =0.023 m

Q: 3. Water is being pumped at 2.5ft3/s. The head loss between points 1 and 2 is 9ft and the power…

A: Given data: Flow of water pumped by the pump: Q=2.5 ft3/s Head loss between point 1 and 2 = hL=9 ft.…

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.