A liquid (SG = 0.920) is being pumped from a reservoir as shown. The pressures at point %3D 1 and 2 are - 8 psi and 44 psi, respectively. The rate of the flow in the pipe is 0.714 ft3/ s. Neglect energy (friction) losses in the system. Use x=4ft, y=7ft, use 1 hp= 550 lb-ft/ s. Efficiency of the pump is 91%. what is the head, in feet, in the pump.

A liquid (SG = 0.920) is being pumped from a reservoir as shown. The pressures at point %3D 1 and 2 are - 8 psi and 44 psi, respectively. The rate of the flow in the pipe is 0.714 ft3/ s. Neglect energy (friction) losses in the system. Use x=4ft, y=7ft, use 1 hp= 550 lb-ft/ s. Efficiency of the pump is 91%. what is the head, in feet, in the pump.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Read the question carefully and give me right solution according to the question
The turbine shown below develops 120 hp (66000 ft Ib/s) when the flow rate of water is 15 ft /s. If all losses are negligible, determine the pressure difference across the turbine (i.e., P4-P3). Answer should be in units of Ib/ft?. (Specific weight of water = 62.4 lb/ft3) P4 12 in.. 12 in. T Free jet
Question 4: H₂=4 m f=0.15 D₁ = 50 mm H₁ 4 m 25 m L = 100 m A. Two tanks A and B were connected by a 50 mm-diameter pipe (f=0.15) that is 100 m in length. Calculate the total flow between the two tanks. B. A pipe of 200mm diameter (f-0.01) and length X is to be connected in series to replace X length of the 50mm pipe. If the purpose is to increase flow by 50%. Find Length X. ***** La=X f=0.01 D. = 200 mm
Plz write neat
The pump whose characteristics are: H, = 80 – 600V²2 %3D n = -1500V² + 700V Elevation = 230 m |(2) (1) Elevation = 200 m 1000 m pipe 40 cm in diameter Pump Figure Q3 is used to pump water (µ=0.001kg/ms) a distance of 1000 m between two reservoirs the elevations of which are shown in Figure Q3 and remain constant. The pipe is 40 cm diameter commercial steel (ɛ=0.046 mm). Ignoring minor losses and assuming fully turbulent flow. Determine d) The volumetric flow rate e) The efficiency at the operating point
Determine the flow distribution of water in the system shown in Figure below. Assume constant friction factors, with f= 0.03. The head-discharge for the pump is Hp = 70 m el 50 m Pipe L (m) D (mm) ΣΚ el 48 m 1 100 750 850 350 200 200 [2] [4] 3 el 0m [5] 4 500 200 350 250 [1] [3]
Consider the figure shown below. If the flow rate of water from the tank is 0.03 m/s, the pressure at point 2 is 120kPa. Height of water in the tank is 4m and the pipe diameter is 160mm with a friction factor of 0.020. Solve for the height h if the branch line is shut off, and if the branch line is open so that half of the flow from the tank goes into the branch and half continues in the main line. Determine the difference in the head losses in both directions. Neglect minor losses. Vent | 4m 160mmø pipe Branch Line B A 1.75m Main Line 300m 200m ANSWER: a. h = 13.918m, b. h = 10.585m c. HL = 3.2479m
Please solve in detail.
PLEASE PROVIDE A COMPLETE SOLUTION WITH FIGURE FOR ME TO FOLLOW :) ANSWER IS GIVEN FOR REFERENCE. THANK YOU!