Two reservoirs A and B have elevations of 250 m and 100 m, respectively. The two tanks are connected by a 250-mm diameter pipe, 250-m long, with a turbine placed along its length. If the flow of water in the pipe is 140 L/s and C = 120, then: El. 250 m N El. 100 m A L = 250 m D = 250 mm C-120 Determine the head extracted by the turbine. 161.1 m O 152.1 m Q=140 L/s TURBINE B

Two reservoirs A and B have elevations of 250 m and 100 m, respectively. The two tanks are connected by a 250-mm diameter pipe, 250-m long, with a turbine placed along its length. If the flow of water in the pipe is 140 L/s and C = 120, then: El. 250 m N El. 100 m A L = 250 m D = 250 mm C-120 Determine the head extracted by the turbine. 161.1 m O 152.1 m Q=140 L/s TURBINE B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Oil (SG = 0.8, y = 0.010 Pa-s) flows through a 10-cm smooth pipe (length: 100 m) at a discharge of 0.010 m³/s, what is most approximately the head loss? O 7.21 m O 5.23 m O 1.28 m O 2.55 m
Assuming that the system is in equilibrium, find the value of m3, knowing that:
What is the gauge reading p₂ in mm of mercury in the below figure ? The turbine develops 370 kW , when a discharge of 2 m³ / sec is flowing through it . Explain
Q4 A pump is used to circulate the water from the lower to the upper reservoir through a pipe system shown in the figure below. The difference in elevation between these reservoirs is 200 m. find the head delivered by the pump and its power if the discharge is 100 L/s? KL = 1.0 "exit Pump KL = 1.5 elbow = 5.0 Pipe length 500 m Pipe diameter 0.25 m K₁=0.8 Pipe roughness=0.004 m HKL
Problem 10.24 A cast iron pipe having a diameter of 100 mm is used to fill the cylindrical tank with water at T = 25°C. The pipe has a total length of 50 m. Suppose that h = 22.5 m. Neglect minor losses. Use the equation # = -1.8 log (Figure 1) Figure €/D 1.11 6.9 + 3.7 Re 2m 1 of 1 Part A Determine the required power output of a pump necessary to fill the empty tank to a depth of 3 m in 6.5 min. Express your answer to three significant figures and include the appropriate units. out = Submit Provide Feedback μA Value Request Answer Units ? 3 of 6 Review > Next >
Energy Equation: Example 2: h₂ 80 m = Datum D = 0.2 m 0.02)V² 2g L = 2000 m- = 0.02 V² D2g A horizontal pipe carries cooling water at 10°C for a thermal power plant. The head loss in the pipe is hL Q = 0.06 m³/s where L is the length of the pipe from the reservoir to the point in question, V is the mean velocity in the pipe, and D is the diameter of the pipe. If the pipe diameter is 20 cm and the rate of flow is 0.06 m³/s, what is the pressure in the pipe at L = 2000 m? Assume a₂ = 1.
a2. answer #3 rush
Three cylinders are piled in a rectangular ditch as shown in the Figure 2 neglecting friction. Wa= 15 Ib, Wb=40 lb and Wc=20 Ib. Determine the reaction between cylinder A and cylinder B. * Rc We Rb B Wb Ah Wa Av FIGURE 2 18 103 lb O None of the Above O 101 Ib О 102 Ib O 100 Ib
i need the answer quickly
WITH SOLUTIONS
3.40 WP To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (a) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe (ks = 35 W/m · K) has an inside diameter of Di1 = 150 mm and wall thickness t; = 10 mm while the outer steel pipe has an inside diameter of Di.2 = 250 mm and wall thickness to = t;. Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation (k, = 0.075 W/m K) between the two pipes does not exceed its maximum service temperature of Tp,max = 70°C. The ocean water is at To,0 = -5°C and provides an external convection heat transfer coefficient of h, = 500 W/m² · K. The convection coefficient associated with the flowing crude oil is h; = 450 W/m2 . K. (b) It is proposed to enhance the…
A sump pump (used to drain water from the basement of houses built below the water table) is draining a flooded basement at the rate of 0.95 L/s, with an output pressure of 1.55 × 105 Pa. Part (a) The water enters a hose with a 2.7 cm inside diameter and rises 2.1 m above the pump. What is its pressure at this point, in pascals? You may neglect frictional losses. Part (b) The hose then goes over the foundation wall, losing 0.65 m in height, and widens to 6.6 cm in diameter. What is the pressure now, in pascals? You may neglect frictional losses.