Water flows through a venturi as shown in the figure at a flow rate of Q=1.3L/s. The inlet and throat diameters of the venturi meter are (D = 3.0 cm and d = 2.5 cm) respectively. The height of water column in the manometers L1 and L3 are 65 and 53 cm respectively. %3D What is the experimental dynamic head at the throat-{section2} (in m)? Li L3 3

Water flows through a venturi as shown in the figure at a flow rate of Q=1.3L/s. The inlet and throat diameters of the venturi meter are (D = 3.0 cm and d = 2.5 cm) respectively. The height of water column in the manometers L1 and L3 are 65 and 53 cm respectively. %3D What is the experimental dynamic head at the throat-{section2} (in m)? Li L3 3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The flow rate of water flowing out of an 80mm diameter nozzle shown in Figure 1 is 60 litre/s. The volume of the water in the pipe bend is 50 litres and the pipe bend is installed in a vertical plane. The head loss from point 1 to 2 is 0.44m. Calculate the x and y for components of the thrust block to hold the pipe bend. Horizontal Thrust block 30° 50° Open end Ø80 mm Ø 160 mm Figure 3 Cs Scanned with CamScanner Vertical
5. Z is a draft tube is a) Temperature difference b) Pressure drop c) Kinetic energy difference d) Datum head View Answer
Props of fluids.
5. Determine the new differential reading along the inclined leg of the mercury manometer of Fig. 3, if the pressure in pipe A is decreased 10 kPa and the pressure in pipe B remains unchanged. The fluid in A has a specific gravity of 0.9 and the fluid in B is water. -SG = 0.9 30⁰ Fig 3 100 mm 50 mm Water 80 mm Mercury
The flow rate of water flowing out of an 80mm diameter nozzle shown in Figure 1 is60 litre/s. The volume of the water in the pipe bend is 50 litres and the pipe bend isinstalled in a vertical plane. The head loss from point 1 to 2 is 0.44m. Calculate the xand y for components of the thrust block to hold the pipe bend.
15. The inverted U-tube manometer is used to measure the difference in pressure between water flowing in the pipes at A and B. If the top segment is filled with air, and the water levels in each segment are as indicated, determine the pressure difference between A and B. pw = 1000 kg/m³. 75 mm 225 mm 150 mm C D B 300 mm
Show the possible arrangement of fluid position in the following pressure measuring devices under specified conditions. 1. Piezometer connected to the side of a water tank containing water up to 2 m depth. 2. Manometer connected to a water tank filled up to 1m and is open to atmosphere. 3. Differential manometer connected to two tanks of 2 m and 1 m diameter filled with water and petrol respectively up to the same level and both are open to the atmosphere. 4. Piezometer with negative pressure. 5. Manometer connected with empty water tank.
Q4: A tank of water empties by gravity through a horizontal pipe into another tank in figure (1) .There is a sudden enlargement in the pipe as shown.At a certain time the difference in levels is 3m.Each pipe is 5m long and has a friction coefficient Cf-0.007 The inlet loss constant is K=0.5 and bore diameter in point A 20mm ,and bore diameter in point B 60mm.Calculate this point. the volume flow rate at Calculate the volume flow rate at this point. (1) 20 mm bore diameter 3 m 60 mm bore diameter (2)
Note:hand written solution should be avoided.
An engineer used a 30 m tape in measuring an inclined ground 459.20 m long. The difference between the starting point and end point is 1.20 m. The tape is of standard length at a temperature of 100 C and a pull of 50 N. During measurement the temperature reading was 15 0 C and a pull of 75N applied at both ends. A= 6.5mm2 ; E = 200GPa; K = 0.0000116 m/C0 . The mass of the tape is 0.075kg/m. Determine the horizontal distance.
Aqb
The circular water pipes shown in the sketch are flowing full. The velocity of flow (in m/s) in the branch pipe "R" is PI V = 6m/s, dia = 4m - = V = ? R Q V = 5m/s dia = 2m