Water at the rate of 86 kg/min is heated from 20 to 70-C by an oil having a specific heat of 1.9 kJ/kg.-C. The fluids are used in a counterflow double-pipe heat exchanger, and the oil enters the exchanger at 110-C and leaves at 70-C. The overall heat-transfer coefficient is 230 W/m2.-C. Calculate the heat transfer rate, kW. (A) 136.2 B) 189.5 C) 300.0 (D) 108.9

Water at the rate of 86 kg/min is heated from 20 to 70-C by an oil having a specific heat of 1.9 kJ/kg.-C. The fluids are used in a counterflow double-pipe heat exchanger, and the oil enters the exchanger at 110-C and leaves at 70-C. The overall heat-transfer coefficient is 230 W/m2.-C. Calculate the heat transfer rate, kW. (A) 136.2 B) 189.5 C) 300.0 (D) 108.9

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

21, from a temperature of water is beine heated 85.1°F to a Aaturated temperatue of 211.4 °F at pressure of 0.101325 mpausing a 2-4 shell and tube heat exchanger. The inlet water mass flow rate =600 kg /min. The heat transfer oil being used is assumed to be stable mineral oil enters at 320 °F, highly refined and with average heat mass flow rate = 148 2 kg /min 0.4498 btu I 16°F capacity Overall heat transfer coefficient 113.3973 btu toztty fina: heeded surface area
To reach the maximum heat exchange rate, if a fan is applied, should it be upward airflow or downward airflow? Need detail explanation. And what will the efficiency difference between upward and downward airflow.
! Required information Consider operation of a single-pass cross-flow heat exchanger with water (cp=4193 J/kg-K) (mixed) and methanol (cp=2577 J/kg-K) (unmixed). Water entering and exiting the heat exchanger at 93°C and 60°C, respectively, is used to heat the methanol initially at 10°C. The overall heat transfer coefficient and the total heat transfer rate is estimated to be 650 W/m².K and 250 kW, respectively. An effectiveness of at least 0.5 is to be achieved. Calculate the mass flow rate of water. (Round the answer to two decimal places.) The mass flow rate of water is kg/s.
A shell &tube heat exchanger has 4 tube passes. Oil inters to the tubes with 100oC . Mass flow rate of the oil is 3 Kg /s and its heat capacity is 2.1 Kj/KgoC. In the shell side air passes with 2 Kg /s Mass flow rate and 1.009 Kj/KgoC heat capacity. Input temperature of air is 20 oC and output temperature is 80 oC. Overall heat transfer coefficient is 200 W/m2 oC. Considering outer diameter of tubs 2cm and tube length 2 m, determine number of tubes in each pass
Consider the steady-state counterflow heat exchanger shown below. There are separate streams of air and water, and each stream experiences no noticeable change in pressure. Stray heat transfer with the surroundings and changes in kinetic and potential energy can be ignored. For the air, the ideal gas model can be applied and Rair = 0.287- For the operating conditions provided on kg-K the figure, determine: a. The temperature of the air at the outlet of the heat exchanger, T4, in [K] b. The rate of heat transfer between the air and the water, in [kW; , c. The rate of entropy production for the heat exchanger, in [kW/K] kg msteam = 12 P1 = 3 bar X1 = 1 P2 = P1 T2 = 200 P3 = 1 bar T3 = 1100 K P4 = P3 T, =? mair kg = 3.29
A single-stage fluid with a mass flow rate of 2.5 kg / s and a heat capacity of 1800 J / kg-K is cooled from 175 ° C to 75 ° C, using a single house fluid with a mass flow rate of 2kg / s and a heat capacity of 2250 J / kg-K during the process. The cold fluid heats from 50C to 150C. For this process, you would prefer to use 1 boiler 2 tube pass heat exchanger or 2 boiler 4 tube pass heat exchanger. Show it mathematically
Concentric Tube Heat Exchanger For equivalent inlet conditions, why should a counterflow heat exchanger have better effectiveness than a parallel unit?
Please show complete solutions and detailed drawings. Show conversions, units, and box in the final answers
Hello Sir,Good Evening. I have a question in my homework related Heat Transfer lesson. The following below is my question. Please Advice. Thank You "Explain the equation used to calculate the heat flux of a counter flow type heat exchanger with a fouling factor using the LMTD concept. Write down the equations involved"
if A 22 C Water enters a heat exchanger with a velocity 0.8 m/s and tube diameter is 10 mm, it leaves at 34 C what is the heat transferred to water. in kW 3.157 O 31.569 O 3.94 O
The purpose of the regenerative heat exchanger is to essentially recycle the heat rejected in step (B) as heat absorbed in step (D). Show why this works for the case of a general working fluid with heat capacity, Cv(T). The Stirling engine (invented in 1816 by Robert Stirling) is a heat engine that produces work through cyclic compression and expansion of a gaseous working fluid, such as hot air. An idealized cyclic process, aptly named the Stirling Cycle, for such an engine consists of four steps: (A) isothermal expansion at the hot reservoir temperature, Th, (B) isochoric (constant volume) heat rejection to a regenerative heat exchanger, (C) isothermal compression at the cold reservioir temperature Te, and (D) isochoric heat absorption from the regenerative heat exchanger back to the initial state.
FLUIO HEATER HEATS 250 kg PER SECOND OF FLUID FROM 35°C TO 100't IN A PARALLEL FLOW HEAT EXCHANGER.THE SPECIFIC HEAT OF THIS FLUID 1s 2.5 kg °C ANEXHAUST GAS WAS USED.FOR HEATING HAVING A SPECIFIC HEAT OF 1 gC, A MASS FLOW RATE OF 625 ks AND AN INITIAL TEMPERATURE OF 200°C THE OVERALL HEAT TRANSFER COEFTICIENT IS 7.5 kw /m2. C.ETERMINE THE FOLLOWING: ) FINAL TEMPERATURE IN °C 2.) AMTD 3) SURFAC E HEAT TRANSFER 4.) HEATING SURFACE IN m2 OTE GAFLUID = QRGAS = HEAT TRANSFERRED TO THE SURFACE SE HEAT CALCULATION FRUM THER Mo 1 AND AMTD FOR THE SURFACE HEAT TRANSFER.