7. An oil heater heats 100 kg per minute of oil from 30°C to 100°C in a counter-flow heat exchanger. The average specific heat of the oil is 2.5 kJ/kg- C. Exhaust gases used for heating enter the heater with an average specific heat of 1 kJ/kg-°C, a mass flow rate of 200 kg/min and an initial temperature of 200°C. The overall heat transfer coefficient is 80 W/m² -°C. Determine the heating surface area in m².

7. An oil heater heats 100 kg per minute of oil from 30°C to 100°C in a counter-flow heat exchanger. The average specific heat of the oil is 2.5 kJ/kg- C. Exhaust gases used for heating enter the heater with an average specific heat of 1 kJ/kg-°C, a mass flow rate of 200 kg/min and an initial temperature of 200°C. The overall heat transfer coefficient is 80 W/m² -°C. Determine the heating surface area in m².

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
Draw Front and Side and top with all dimensions please
DRAW THE ISOMETRIC FIGURES OF THE ORTHOGRAPHIC DRAWINGS BELOW.ADD DIMENSIONS AND LEADERS
Choose the correct answer below and show your solution completely. Make sure that your finals answer is 4 decimal places.
Round off the numbers in the following problems to three significant figures. Find the percent difference between each rounded-off number and the original number by using the original number as the reference. 6748.3
Draw the right side elevation of the object with the given top and front elevations below
The wind chill (i.e. how cold it actually feels) is given by W(T,v) = 35.74 +0.6215T – 35.75v0.16 + 0.4275Tv0.16 degrees Fahrenheit when the actual air temperature is T degrees Fahrenheit and the wind speed is v miles per hour. Enter the function into your Y1 and verify that W(-5,15) = -25.80216395. Ploti Plot2 Plot3 1 -25.80216395 Y1835.74+0.6215T=5 T-35.75V0.16+0. V=151 4275TV6. 1Ği bound=(-1e99,1. Ýs= Use this function to answer questions 1 - 8.
Draw Front and Side and top with all dimensions please
Round off the numbers in the following problems to three significant figures. Find the percent difference between each rounded-off number and the original number by using the original number as the reference. 26.394
Use Share Sketch to create this part with one sketch. Pivot lock (dimensions are in inches. The circular features in the design are all aligned to the two centers at the base.
Please help show me how drawing will look in isometric drawing.
Draw front and right-side views of the following object with a completed dimensions. Draw in scale 1:1 on A4 sheet. (Problem is taken from "Graphics for Engineers' by Earle) 78 What can we learm from the drawlng ? 1. The dimension note M10x1.5 means that the hole is a threaded hole. R16 O 16, 2 Holes The letter 'M' means that the threads are made by following a metric thread system. The number "10" Is the major dlameter of the hole and the number 1.5 is the pitch of a thread. However, for coarse threads, it is a common practice to omit specifying the pitches. For example, a note M10 means the pitches of the thread is 1.5 mm. In this book, the pitch is specified in order to facilitate drafting. 2. Drawing symbol of a threaded hole is shown below. - Thin Ine (4H pench The ends of this arc does not meet together but approximately 90 degs, apart. Object Ihe (2i pencil .major dlameter pich2 M10x1 5 3. The circular projection surface at a threaded hole that is raised from a cylinder is…