Water at 20°C flows through a 6 cm diameter pipe which has a 180° vertical bend, as in Fig. The total length of pipe between flanges 1 and 2 is 75 cm. When the mass flow rate is 31.89 kg /s, Gauge pressure at p1 = 76 kPa, and p2 = 47 kPa. Neglecting pipe weight, determine the X component ( Shown on figure ) of the force to the nearest N which the flanges must withstand for this flow.

Water at 20°C flows through a 6 cm diameter pipe which has a 180° vertical bend, as in Fig. The total length of pipe between flanges 1 and 2 is 75 cm. When the mass flow rate is 31.89 kg /s, Gauge pressure at p1 = 76 kPa, and p2 = 47 kPa. Neglecting pipe weight, determine the X component ( Shown on figure ) of the force to the nearest N which the flanges must withstand for this flow.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows through a Venturi meter, as shown in the figure. The pressures of the water at locations a and b in the pipe support columns of water that differ in height by L = 12 in. The atmospheric pressure is 14.7 lbf/in2, the specific volume of water is 0.01604 ft3/lb, and the acceleration of gravity is g = 32.0 ft/s2.
Flow takes place between three reservoirs, as shown in Figure 1. The volume flow rate out of reservoirs A and B is 0,15 m³/s and 0,25 m³/s respectively. If the coefficient of friction for three pipes is 0,008, determine the relative elevations of the free surfaces. Neglect all losses other than friction. May you kindly resend the answers in a different format as they appear blank??
Please don't provide handwritten solution .....
3. (a) A nozzle of inlet area A₁ and exit area A2 exhausts to atmosphere. A fluid of density p enters the nozzle with pressure p₁ (gauge) and velocity u₁. Show that the force trying to separate the nozzle from the pipe is given by 2 F = P₁A₁ - pA₁u₁² whether the nozzle is frictionless or not. A₁ A₂ -1)
A cylinder with a mass 0.222 kg is sliding downwards through a vertically positioned pipe. A thin oil layer exists between the cylinder and the pipe's internal surface. Centerline of the cylinder and the pipe overlap. (yoil =8044.2 N /m3 ; voil=6-106 m²/s). Find the change in the speed of cylinder in the pipe with respect to its unit displacement and the shear stress that acts upon the oil layer. A A L = 128 mm V W 73.8 mm 74 mm 0.1 mm Figure 1
Water flows through a Venturi meter, as shown in the figure. The pressures of the water at locations a and b in the pipe support columns of water that differ in height by L = 10 in. The atmospheric pressure is 14.7 lbf/in², the specific volume of water is 0.01604 ft3/lb, and the acceleration of gravity is g = 32.0 ft/s². Step 1 Patm = 14.7 lbf/in.² g= 32.0 ft/s² Determine the difference in pressure between points a and b, in lbf/in². Does the pressure increase or decrease from point a to point b? Water v = 0.01604 ft³/lb Save for Later Determine the difference in pressure between points a and b, in lbf/in². Pb-Pa = i lbf/in² 4 Attempts: 0 of 4 used Submit Answer
Water at 20°C flows through a 11.5-cm-diameter pipe that has a 180° vertical bend, as in the figure. The total length of pipe between flanges 1 and 2 is 75 cm. When the weight flow rate is 230 N/s, p1-165 kPa and p2-134 kPa. Neglect pipe weight. Determine the magnitude of the horizontal force balance that the flanges must withstand for the flow. The magnitude of the horizontal force F=-
Don't give handwritten solution
the open tank in the figure contains water and is being filled through section 1. Assume incompressible flow. If the water level h is constant, determine the exit velocity V2 for the given data V1 = 3 m/s and Q3 = 0.01 m3/s.
could you please help me calculate the verical force (in Newtons) on the door at time t=0
Find the inlet velocity without copying from others source,ASAP
In a horizontal pipe water flows at a rate of 9.1 L/s. Here, the pipe has two sections, one with a diameter of 10.16 cm and the other with a diameter of 5.08 cm, with a gradual smooth reducing section. In this case, a mercury manometer is used to measure the pressure difference. If friction is negligible how would I find the differential height of mercury between the two sections? If the manometer on the 5.08cm pipe section was replaced with a pitot tube how would the reading change? any help would be deeply appreciated