Water at 15°C (p = 999.06kg/m², µ = 1.1373 x 10-³Pas) is flowing steadily in a 28-m-long and 6.7-cm- diameter horizontal pipe made of stainless steel at a rate of 26 L/s. Determine the head loss along the pipe section. Given that the absolute roughness of stainless steel is ɛ = 0.0025 mm. %3D

Q: A reservoir at 300 ft elevation has a 6-in.-diameter discharge pipe located 50 ft below the surface.…

A: Given: elevation of the reservoir→Z1=300 ft And elevation of the outgoing flow →Z2=150 ft Diameter…

Q: Water at 40°F (p=62.42 lbm/ft3 and µ=1.038x 10-3 Ibm/ft · s) is flowing through a 0.12-in diameter…

A:

Q: Consider a flow of SAE 30W oil at 20°C through a 2.4-cm-diameter smooth pipe at 1 million N/h.…

A:

Q: Gasoline (p = 680 kg/m² and v = 4.29 × 10o-7 m²/s) is transported at a rate of 190 L/s for a…

A:

Q: Air flows in an 8-cm-diameter, 33-m-long pipe at a velocity of 5.5 m/s. The piping system involves…

A: The data given is, Length of pipe, L = 33 m Velocity of flow, V = 5.5 m/s Total minor loss…

Q: A pitot tube with diameter of 3 cm is installed in a pipe with ID 150 mm. Water flows through the…

A:

Q: Rainwater flows through the galvanized iron downspout shown in the figure below at a rate of 0.005…

A:

Q: Two pipes of identical diameter and material are connected in parallel. The length of pipe A is four…

A: Given data as per the question length of pipe A = four times the length of pipe B

Q: Water flows at an average velocity of 10 m/s through a horizontal tube of diameter 5 cm. The…

A: Note: Since you have posted a question with multiple sub-parts, we will solve first three sub- parts…

Q: Rainwater flows through the galvanized iron downspout shown in the figure below at a rate of 0.009…

A: The size of the downspout cross-section.Given:The flow rate is .The downspout is shown below.

Q: Water at 20°C flows through the piping junction, entering section (1) at 0.1 m3/min. The average…

A: Given figure:

Q: Two tanks are connected by a piping system made of commercial steel. The system is composed of pipes…

A: Answer: Volumetric flow rate = 0.0121 m3/s Direction of flow = from tank 2 to tank 1 Images of the…

Q: Water is pumped from the river through a 45-mm-diameter hose having a length of 2.5 m. The friction…

A:

Q: Two pipes of identical diameter and material are connected in parallel. The length of pipe A is five…

A: Given data: The length of the pipe A, LA = 5L. The length of the pipe B, LB = L. As both the pipe…

Q: What does "viscous flow" mean, and what does "head loss through friction" mean? Describe the…

A: Viscous flow refers to the flow of fluids in which there is a resistance to motion due to the…

Q: To conserve water and energy, a flow reducer is installed on the neck of a shower. If the pressure…

A:

Q: Water is pumped through a 60-m-long, 0.3 –m-diameter pipe from a lower reservoir to a higher…

A:

Q: A vented tanker is to be filled with fuel oil with Density= 920 kg/m3 and Viscosity =0.045 kg/m s…

A:

Q: Determine (a) the head loss, (b) the pressure drop, and (c) the pumping power for water flowing…

A:

Q: Consider fully developed laminar flow in a circular pipe. If the diameter of the pipe is reduced by…

A:

Metrology of surface finish

In general terms, the application of scientific principles in the study of measurements is known as metrology. When speaking about measurement, it could be of time, length, microstructures, grain structures, internal crystal discontinuities, surface roughness, measurements of angles, height, width, and so on. While coming to the domain of mechanical engineering, metrology is considered the science of measurements of surface finish, length, surface texture, and angles.