Two tanks are connected by a piping system made of commercial steel. The system is composed of pipeswith diameters of 0.1 m and 0.05 m. The viscosity of the water is u = 1.2 x10-3 Pa s. When the gatevalve is opened completely, what is the expected volumetric flow rate and in which direction will the flowbe?P2 = 100kPa20 mHgate valve0.05 m20 m50 mP1 = 250kPaNot to scale25 m0.1 m10 m H2030 m

Answer: Volumetric flow rate = 0.0121 m3/s Direction of flow = from tank 2 to tank 1 Images of the…

Answered: Two tanks are connected by a piping…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

piping system can be neglected but the minor loss at the exit can't be neglected. What is the total head loss in the system, i.e. free surface to pipe exit? What is the minor loss at the exit? volumetric flow rate at the exit is 0.01 m³/s. Assume the minor loss at the entrance of the The valve is partially open. The pipe is made of commercial steel (ɛ = 0.046 mm). The 4. Water is being discharged from a very large reservoir via the piping system shown below. What is the loss coefficient at the exit? Water p=1000 kg/m3 5 m p=0.001 kg/(m s) 0.1 m Q=0.01 m3/s 25m
Water is flowing in a round tube. The temperature is . , and the dynamic viscosity is . The tube inside diameter is . The Reynolds number is . What is the friction factor? ____________
State clearly your assumptions in your solution sheet
Compute the Cross sectional area of Pipe Discahrge=0.8 m3/s Velocity=2 m/s
Please help, will give helpful ratings if correct!!!
The velocity of the fluid flowing thru a 50 mm diameter pipe is 1.35 m/s. The fluid hasa kinematic viscosity of 5.3 x 10-6m2 /s. If the pipe has a length of 200 m: a. Determine the Reynold’s Numberb. Compute the friction factorc. Compute the head loss of the pipe
Water (specific gravity, G, is 1.0 and the kinematic viscosity, ν, is 1.14 *10-6 m2 /s) flows through a piping system with a flow rate of 0.9 m3/s. The pipe is 2800 m long and 600 mm inside diameter. The pipe has three gate valves, two globe valves, one swing check valve, three standard teesthrough-branch, and four 90o standard elbows. Calculate the following:a- The total length of that piping system.b- Is the flow laminar or turbulent?
The pressure drop in a horizontal commercial steel pipe should not exceed 1 psi per 150 feet of pipe length for flow rates up to 500 gal/min. If the water temperature is never below 50 F°, determine the necessary pipe diameter.
A pipe has a diameter D and a friction factor f. Assume that f is constant due to a very large reynolds number. By what percent will the pressure drop in the pipe increase if the volume flow is doubled?
The diameter of the smooth pipes used in the pumping system in the lower figure is 150 mm and its total length is 80 m. In this system, there are four elbows with a loss coefficient of 0.2. It's lost its coefficients are 0.5 for the inlet to the pipe, 0.7 for the valve and 1 for the inlet to the tank. z2-z1=15 m, above manometric pressure if the flow of water pumped into the tank is 50 L/s and the overall efficiency of the pump is %84 find his height and strength. Take the viscosity of water is 0.001 kg / m.s
Calculate the average and maximum velocities of a fluid flowing at the rate of 20 L/min through a 1 1/2 in. sanitary pipe. The fluid has a density of 1030kg/m3 and a viscosity of 50 centipoises. Is the flow laminar or turbulent?
8- Oil flows in the circular pipe at 40 oC. If the Reynolds number is calculated as 1700, what is the friction factor?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS