Water 60°F flows at 10 ft/s in a 3 in. diameter pipe that is 100 ft long. There are six elbows (KL = 1) and two gate valves (KL = 0.3). The end of the pipe is at elevation 20 ft above the inlet. The pressure at the inlet is 50 psia. The roughness height is 0.0002 ft. Determine the head at the inlet, head loss,pressure drop due to losses, and absolute pressure at the end.  *Show your correct and complete solution. Please include schematic diagram and assumptions.*

Q: Glycerin at 40°C is flowing through a 4-cm-diameter horizontal smooth pipe with a flow rate of 6…

A: Now we Reynolds number Re=ρVDhμρ=Density of the fluidDh=Diameter of the pipeV=Flow rate μ=Dynamic…

Q: 3. Water at 20°C flows through a smooth pipe that is 50 cm in diameter and 2 km in length. If the…

A:

Q: Pressures at the start and end of a straight horizontal pipe pumping water are measured as…

A:

Q: Water at 30°C flows at 120 L/s inside a forged steel pipe shaped as an equilateral triangle of 50 cm…

A:

Q: A reservoir at 300 ft elevation has a 6-in.-diameter discharge pipe located 50 ft below the surface.…

A: Given: elevation of the reservoir→Z1=300 ft And elevation of the outgoing flow →Z2=150 ft Diameter…

Q: Glycerin at 20 °C flows upward in a vertical 75-mm-diameter pipe with a centerline velocity of 2.0…

A:

Q: head loss due to sudden contraction valve in a piping system is much higher than gradually…

A:

Q: Oil ( μ = 0.478 Pa.s and ν = 5.3 *10-4 m2/s ) flows downward in a pipe which is ( 3 cm ) in diameter…

A:

Q: Heavy oil flows in a 40 cm diameter cast iron pipe f= 0.044. If the head loss due to pipe friction…

A:

Q: Water at 59 F flows through a straight section of a 6-in-ID cast-iron pipe with an average velocity…

A: Given dataT=59FV=4 ft/sg=32.2 lb.ft/s2ρ=62.3 lb/ft3y1-y2=2ft

Q: Water is conveyed from a constant head tank (head or operation is 4 m) through a 100 m long…

A: To Find: Loss coefficient for value i.e. K Given that, H=4 m, L=100 m, d=100 mm=0.1 m Q=12…

Q: Water is flowing in a conical tube. the inlet conditions are D=100mm, v=1m/s & density = 1000kg/m3.…

A:

Q: Heavy oil is flows in a 40 cm diameter cast iron pipe f= 0.044. If the head loss due to pipe…

A:

Q: Water flows at a rate of 2.4 ft3/s in an old, rusty 7.8-in.-diameter pipe that has a relative…

A: Given;

Q: A smooth plastic pipe is to be designed to carry 10 (ft^3)/s of water at through 1800 ft of…

A:

Q: A 230-m-long pipeline delivers 20°C water to a storage reservoir located downstream. The pipeline is…

A:

Q: Water flows at the rate of 0.80m3/s in a 900-m long pipe. The total head loss in the pipe is 4m.…

A: GIVEN DATA - Q=0.80 m3/s L=900m h=4m f=0.018 We have to find diameter of pipe using Darcy-Weisbach…

Q: A straight pipe has a daimater of 25 mm, a roughness height of 0.1 mm, and is inclined upward at and…

A: Write the properties of water at 10°C. Draw the diagram of the pipe. From the diagram,

Q: Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m ) is to be pumped through 50 m of pipe…

A: for solution refer below images. Note:- since loss coefficient for abrupt expansion is not given i…

Q: The observed pressure drop for 40°F water flowing at 16 ft/min in a 4.5-in diameter pipe is 9.68 x…

A:

Q: A water jet exits from the nozzle to the atmosphere as shown in fig.(1), if the pressure at section…

A: according to the given details

Q: Water is flowing through the 40 mm pipe shown below at 250 L/min. The pressure at point 1 is 5322…

A: Given:d=40 mmQ=250L/min P1=5322 KPaP2=4358 KPaP1'=5081 KPaP2'=1222 KPa

Q: A venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a…

A: Given data: D=300 mmd=100 mmP=150 kPaHead loss=3% of differential pressure headhloss=-400 mm Need to…

Q: What does "viscous flow" mean, and what does "head loss through friction" mean? Describe the…

A: Viscous flow refers to the flow of fluids in which there is a resistance to motion due to the…

Q: Oil (with kinematic viscosity ν = 4x10-5 m2/s and specification SG= 0.9) flows from the upper…

A: Introduction: When fluid flows from one location to another, the head lossless comes into play. The…

Q: A fluid of density 835 kg/m flows at 2.4 m/s from a pipe of diameter 17 mm into to a pipe of…

A:

Q: Water at 20°C is pumped through a smooth 12-cm-diameter pipe 10 kmlong, at a flow rate of 75 m3/h.…

A:

Q: Water (@ 45°C) is flowing in a horizontal pipe with an increasing cross-sectional area. The measured…

A: Given   Pressure drop = 4.1 psia                            = 28268 Pa         Exit area, A = 2a…

Q: Water at 20°C is pumped through a smooth 12-cm-diameter pipe 10 kmlong, at a flow rate of 75 m3/h.…

A:

Q: In an annular section made of commercial steel pipe with an outer diameter of 13.78 inches inside a…

A: Given data Annular section with Outer Diameter = 23.62 inch = 0.59995 m Inner Diameter = 13.78 inch…

Q: Pressure drop between two sections of a unifrom pipe carrying water is 9.81 kPa. Then the head loss…

A:

Q: The velocity of water is measured using an orifice meter (throat diameter = 0.06m) in a 0.31-m…

A: Given       Height, h = 0.31 m Diameter, d  = 0.06 m Viscosity = 8.90 × 10−4 Pa·s  Find   Reynolds…

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.