Rainwater flows through the galvanized iron downspout shown in the figure below at a rate of 0.009 m³/s. Determine the size of the downspout cross section if it is a circular and it is completely filled with water. Neglect the velocity of the water in the gutter at the free surface and the head loss associated with the elbow. 70 mm ↓ 4 m f -3 m

Rainwater flows through the galvanized iron downspout shown in the figure below at a rate of 0.009 m³/s. Determine the size of the downspout cross section if it is a circular and it is completely filled with water. Neglect the velocity of the water in the gutter at the free surface and the head loss associated with the elbow. 70 mm ↓ 4 m f -3 m

Name: Rainwater flows through the galvanized iron downspoutshown in the fig
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Rainwater flows through the galvanized iron downspoutshown in the figure below at a rate of 0.009 m³/s.Determine the size of the downspout cross section if it isa circular and it is completely filled with water. Neglectthe velocity of the water in t

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is flowing in a conical tube. the inlet conditions are D=100mm, v=1m/s & density = 1000kg/m3. determine the velocity of the water at the discharge point. The outlet diameter is 200mm. a. 0.18b. 0.1c. 0.5d. 0.25
A nozzle is attached to a pipe as shown in Fig. 8-33. The inside diameter of the pipe is 100 mm, while the water jet existing from the nozzle has a diameter of 50 mm. If the pressure at section 1 is 500 kPa, determine the water's jet velocity. Assume head loss in the jet is negligible.
A 5 cm diameter potable water line is to be run through a maintenance room in a commercial building. Three possible layouts for the galvanized iron water line are proposed as shown in the figure. The bends are conventional threaded fittings. Select the option that minimizes losses and determine the pressure drop for a flow of 350 L/min. For the elbo losses use, hℓm =
I need the answer as soon as possible
Water enters a piping system with a diameter of 0.1016 m from a reservoir with a volumetric flow rate of 0.1893 m³/min. Determine whether the flow is laminar or turbulent if, during the winter, the dynamic viscosities of μ = 1.308x 10-3 Pa 's and 0.687x10-3 Pa s during the summer. What is the length of pipe necessary to reach a fully developed flow?
A long 0.3 m pipeline laid between two reservoirs carries a flowrate of 0.14 m3/s ofwater. A parallel pipe of the same friction factor is laid beside this one. Calculate the approximatediameter of the second pipe if it is to carry 0.28 m3/s
Water at 15°C is pumped from a reservior at a rate of 0.2428 m³/s where the local atmospheric pressure is 96.5 kPa. The total head loss in the suction pipe is 1.1 m. From the manufacturer data, the NPSH required at this operating point is 6.6. Determine the maximum height hs (meters) before cavitation can occur. Round off your answer to 3 decimal places. (10 mins) hs Vs Suction pipe Free surface of liquid Sump
answer 2nd question
Question 1 A pipeline of length 2000 m and diameter 200 mm connects two water supply reservoirs together. (a) If the value of the frictional factor, f, for the pipeline is 0.02 then determine the flow in the pipeline when the head difference between the two reservoirs is 20 m. (b) If an increase in demand requires that the flow be increased by 40% then determine what length of the same diameter pipe is required to satisfy this demand if it is connected as shown in Figure 1. Assume that the friction factor for the new pipe is the same as the existing one. New pipeline 20 m
None
Water flows through the screen in the pipe shown in the figure below as indicated. Determine the loss coefficient for the screen. Assume V = 22 ft/s, h = 5 in. k = i Screen Water SG = 3.2
Glycerin flows through the pipe of diameter 41 mm at temperature of 15∘C with flow rate of 0.003 m3/s. Determine the head loss in the pipe where the total length of the pipe is 23 m.