1) Water flows through the 100-mm-diameter pipe at 0.035m³/s. If the pressure at A is475 kPa and the head lossbetween A and C is 1.5 m,determine the pressure at C.الشعبة-2 mالاسمن100 mm100 mmAB30°Datu4 m-2 m-

Answered: Image /qna-images/answer/bd852d20-36ee-4176-bea0-4c797b129cfc.jpg

Answered: 1) Water flows through the 100-…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Oil with a specific gravity of 0.83 and a dynamic viscosity of 8.5 × 10^−3 Pa ∙ s flows at a rate of 502 L/min into the open tank. The total length for the DN 50 schedule 40 steel pipe is 37 m, while the length for the DN 100 schedule 40 pipe is 100 m. Determine the pressure at point A.
3. Water (assumed inviscid and incompressible) flows steadily in the vertical variable-area pipe shown in Fig. Determine the flowrate if the pressure in each of the gages reads 50 kPa. -2 m- -1m- 10 m p = 50 kPa
Oil of SG=0.87 and a kinematic viscosity v = 2.2 x 10-4 m²/s flows through the vertical pipe shown in the figure below at a rate of 5 x 10-4 m³/s. Determine the manometer reading, h. Assume SGm = 1.3, D = 18 mm, / = 3 m. h = i SG m te SG SUPPORT
The T-junction has discharges Q1=0.3 m3/s, Q2=Q3=0.15 m3/s, and has diameter D1=0.45 m, D2=0.3 m, and D3=0.2 m. Determine the magnitude and direction if the upstream pressure is 1500 kN/m2
3 - Oil flows through the horizontal pipe under a pressure of 400 kPa and a velocity of 2.5 m/s at A. Determine the pressure in the pipe at B if the pressure at C is 150 kPa.Disregard any difference in elevation. Consider the specific mass of the oil equal to 880 kg/m3.
4. Two reservoirs, A and B, are connected by a pipeline which is 1300 m long. The surface of reservoir B is 10 m lower than that of reservoir A. There is a small hill between the two reservoirs with the highest point at 500 m along the pipe from A. If the pipeline has a diameter of 300 mm and a friction factor of λ = 0.008 then determine the following: (Ignore the minor losses and assume that the pipe is already flowing full and at a steady flow) (a) The flow in the pipe (b) If the lowest permissible absolute pressure head in the pipeline is 2.5 m of water, determine how high above reservoir A surface level the pipe can be laid so that the minimum pressure condition is satisfied. (Assume atmospheric pressure of 105 Pa.)
Water flows into the pipe connection shown at '6' and '2' and leaves the system at '1'. It is not open to the atmosphere at any connection. The gauge pressure at both inlets is 12 psig and the velocity at both inlets is 9.5 ft/sec. Determine the horizontal force (lbf) needed to hold the fittings in place. 2 7.5" 1 2.5" 3 4 5 6 1.0"

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

1) Water flows through the 100- mm-diameter pipe at 0.035 m³/s. If the pressure at A is 475 kPa and the head loss between A and C is 1.5 m, determine the pressure at C. الشعبة -2 m الاسمن 100 mm 100 mm AB 30° Datu 4 m -2 m-