Water at 10 C flows in a 3-cm-diameter pipe at a velocity of 1.5 m/s. The Reynolds number for this flow is ? 34420 QUESTION 2 Air at 1 atm and 20 C flows in a 2.5-cm-diameter tube. The maximum velocity (m/s) of air to keep the flow laminar is ? 1.64 QUESTION 3 Consider laminar flow of water in a 0.9-cm-diameter pipe at a rate of 1.25 Lmin. The velocity (m/s) of water halfway between the surface and the center of the pipe is ?

Water at 10 C flows in a 3-cm-diameter pipe at a velocity of 1.5 m/s. The Reynolds number for this flow is ? 34420 QUESTION 2 Air at 1 atm and 20 C flows in a 2.5-cm-diameter tube. The maximum velocity (m/s) of air to keep the flow laminar is ? 1.64 QUESTION 3 Consider laminar flow of water in a 0.9-cm-diameter pipe at a rate of 1.25 Lmin. The velocity (m/s) of water halfway between the surface and the center of the pipe is ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Fluid originally flows through a tube at a rate of 100 cm3 /s . To illustrate the sensitivity of flow rate to various factors, calculate the new flow rate for the following changes with all other factors remaining the same as in the original conditions. (a) Pressure difference increases by a factor of 1.50. (b) A new fluid with 3.00 times greater viscosity is substituted. (c) The tube is replaced by one having 4.00 times the length. (d) Another tube is used with a radius 0.100 times the original. (e) Yet another tube is substituted with a radius 0.100 times the original and half the length, and the pressure difference is increased by a factor of 1.50.
Air is flowing through a 19.6-cm diameter pipe with a velocity of 6.05 m/s. If the temperature of the air is 21.29°C and pressure is 102 kPa, compute the flow rate of air in the pipe in kg/s.
If the difference between the total pressure and static pressure in an air duct is measured by a pitot tube to be 6.5 cm H2O, what is the flow velocity in m/s? Density of water is 998 kg/m3, and g = 9.81 m/s2. 3 signififcant figures answer
Question 3 Water (p = 1000 kg/m³, μ = 1.12 x 10-3 Ns/ m²) flows through a 0.01-m-diameter pipe at a velocity of 2 m/s. The length of the pipe is 40 m. A pump is used to maintain the flow from one reservoir to another reservoir as shown. The following data are available: KL elbow = 1.5, Kentrance = 0.5, Kexit = 1.0. Elbow Pump Elbow Figure Q1 Note that the entrance and exit are at the same elevation. The free surfaces of the reservoirs are also at the same elevation. (a) Calculate the total head losses in the pipe.
Calculate the pressure differential and head loss in a 70-cm-diameter pipe using a 40-cm-diameter orifice meter if the water has a volumetric flow rate of 380 L/s, a density of 998 kg/m, and a dynamic viscosity of 1.002 x 10-3 kg/m-s.
Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps please
Water drains from a pressurized tank (50 kPa gage) through a 0.1m-diameter pipe system at a rate of 0.0371 m³/s. If the density of water is 1000 kg/m³ and the dynamic viscosity is 1.12 x 10 - 3 Ns/m², the Reynolds number would be equal to O 3312 O 25893 O 422321 O 475892
Air flows from a 10cm pipe in which the temperature and pressure are 4-C and 280kpa, respectively, into a 5cm pipe in which the pressure is 147kpa gage. Calculate the velocity and discharge in each pipe, assuming isothermal conditions, standard atmospheric pressure and no losses. The gas constant for air is 280N-m/kg-K.
In the flow of water through a capillary tube, if the diameter of the tube is increased by 3 times its original value with no other changes, the flow rate will O a increase by a factor of 27 Ob increase by a factor of 81 C increase by a factor of 9 d increase by a factor of 16
Liquid flows at a rate of 1.5 L/min in a circular tube with a diameter of 5 mm. inside a circular tubeThe vascular endothelial cells are attached. One cell has a surface area of 500 μm2. To be attached to the inner wall of the tube. What force does one cell have to withstand? The viscosity of the liquid is 1.2 cP = 0.0012 Pass.
Heated air at 1 atm and 100°F is to be transported in a 900-ft-long circular section plastic duct at a rate of 1.4 lb/s. I want to determine the head loss and pumping power at the three diameter values in the table below. Complete the table to help me choose a wise diameter. Why would a good design not only focus on minimizing the pumping power? Diameter Head loss, hi Pumping power, W Reynolds number, Re n.d. f n.d. (in) ft hp 8 12 16
Air is flowing through a 20.27-cm diameter pipe with a velocity of 5.61 m/s. If the temperature of the air is 23.68°C and pressure is 114 kPa, compute the flow rate of air in the pipe in kg/s.