wainG Stuffness method of An alyas , Determne the stresses a bars A1B A: 100 mm Steel a Bi 50 mm Ø steel 100 N 5ON Use E -20,000 mPa in Fig io somm 200mm

Q: A state of stress at a point A is given by ox = 125 MPa, oy 88 MPa, and txy = 40 MPa. Which of the…

A: Given: The value of stress at point A is,σx=125 MPa. The value of shear stress is, τ=40 MPa. The…

Q: A Brass C AL B 0,6m A = 1130 mm² T₁ = 10°C → no load Cale stress at T= 50°C What is the displacemed…

A: Given: Initially there is no load for the given system. Initial temperature for the assembly:…

Q: Find the stresses at point C. -1.5 m 2.5 m 250 mm 125 mm 1.5 m 50 kN/m 50 mm 2 m 4m

A: Find the stresses at point C.

Q: Figure Part A 3 kip μà -1.5 ft d= Value Determine the minimum diameter d of the rod to safely…

A:

Q: Segments AB and CD of the assembly are solid circular rods. A) What is the normal stress in segment…

A:

Q: A 260 mm bar AB with a rectangular cross section of 17 × 30 mm, consists of two aluminium layers…

A:

Q: The vertical force F applied at A is 50 kN. Compute the minimum diameter of the steel wire, if the…

A: Given: F = 50 kN Allowed elongation of steel wire, ∆Lall = 4 mm Maximum stress, σmax = 250 MPa Est =…

Q: The bolt in the following figure when tightened, we measure a &13µm decrease in the bolt diameter d.…

A: Given data:-diameter of bolt, d=60mmchange in diameter of bolt, Δd=-13μm=-0.013mmModulus of…

Q: under Stiven : load of 66 kip. The diamurer of Rod decrease 0.004 in during load Find average normal…

A: Given              Diameter, d = 2 in                     Load, P = 60 kip Change in diameter =…

Q: Please Show work clearly and show free body diagram if possible and be sure with the positive and…

A:

Q: b=3./m a=2.1m (1) B C = 2m (2) P = 80kN C d = 1.8m WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN MPa…

A:

Q: Question 1 a = 2.1m (1) c=2m b=3./m d = 1.8m P = 80 kN WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN…

A:

Q: bläi 10 FIND STRESS IN Aluminum. IF E st= .200000 MPa, Ealu.=7000O MPa 100 kN RALU30 MM Aluminum…

A:

Q: Figure < 1 of 1 - 2 in. 0.5 in. - 2 in.-

A: For solution refer below images.

Q: 2) Find the axial stresses of members FD, GD, GE. State if it is tensile or Compressive. E 3m 5o kN…

A: Consider horizontally forward &amp; vertically upward reaction as (+)ve and horizontally backward…

Q: Problems Determine the stress in each material if the left wall yields 0.6mm Bronze A=2400mm E=83G…

A:

Q: Find the rertical if Pis 20KN movement of P Steel Aluminum 4m 2m Im B

A:

Q: A thick cylinder is built up by shrinking an aluminium tube 20mm thick upon a hollow aluminium…

A:

Q: 4- Determine the stress when Temperature change from 20 C° to 60 C° . steel aluminum 20 kN 200 mm…

A:

Q: The 30 kN load is acting on the 4.25 cm´ area of the steel rod due to the stress…

A: Given data: A=4.25 cm2kt=2.1P=30 kN Need to determine the maximum stress.

Q: Find the stresses in A, B and C?

A:

Q: An aluminum pipe is filled in concrete is subjected to a pure compressive force as shown in the…

A: When an external force is applied to any body the body gets deformed. This deformation is resisted…

Q: Rod ABC has a diameter of 30 mm at AB and diameter of 20 mm at BC. the whole rod is subjected to a…

A:

Q: b. 20 kN/m B I'm 7m SOKN/m C Im

A: Given: For the 20 KN/m force the length is 1 m For the uniform variable force from 20 KN/m to 80…

Q: 2. (practice problem for Exam 1) Find out the normal stress throughout the bar. - Hint: you should…

A:

Q: The principal stress o1 is ksi

A:

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: given from the above diagram,From the FBD of joint B, we get

Q: 5. Find 2 in 口2 im 300 lb-ft cosS - Section V80 lb it =33.9 psi Tonia Ob -b =8.48 psi TL-b= 147 Psi…

A: Let us consider tension force in inclined member is P. Drawing FBD of horizontal member:

Q: A rectangular plate with a hole is shown in fig that carries a tensile load. Stress value calculated…

A: Given that  A rectangular plate with a hole is shown in fig that carries a tensile load. Stress…

Q: in A Composite bar Çansists af Q1) an aluminum Section rigidly fastened between as shown in fiqure…

A:

Q: Meckenieal Design EnginziNG Calculate the maximum tensile stress in the bracket as shuwn beln. G0 mm…

A: L=400 mmCross section =80 mm×20 mmAxial load P=4.2×sin40°=2.6997 KNTransverse load…

Q: DATE: A 01. The member consists of the steel rod AB that is screwed into the end of the bronze rod…

A: As per given question  Steel  AS=400 mm2 LS=1m ES=200gpa Bronze Ab=650mm2 Lb=2m ES=80 gpa We have to…

Q: with a stress of 52.89  and diameter of 4cm and thickness of 2mm  (P) load of 2MPa how was the…

A:

Q: A -0.5 m- 400 KN B -0.5 m- C 0.4 m D E F Figure 2 (not to scale) The assembly shown in Figure 2…

A: Answer: ◆ The normal stress in post AD and CF: 168 MPa. ◆ The normal stress in post BE: 43 MPa.

Q: Maximum shear stress (Tresca) criterion whether the diameter d is safe using ch

A:

Q: What will be the maximum diameter of a metal rod, which is used to raise a load of 2400N if the…

A: