Using the data given in the table below, calculate the Ihher uldimiele Parameter Magnitude Parameter Magnitude Modulus of elasticity 200 GPa Free deformation coefficient 77 Engine sped 6000 rpm Drive shaft outer diameter 110 mm Specific weight 78000 N/m3 Drive shaft length 860 mm Use: ncr = 1.1 ne a. 0.097 b. 0.096 c. 0.095 d. 0.094

Q: Describe Pascal’s law?

A: Pascal’s law states that the static pressure acted on a liquid particle at rest is normally towards…

Q: What are the two most common systems of units?

A: Given Data⇒ systems of units Problem statement⇒ Problem says What are the two most common systems of…

Q: Give an example of concentrated force.

A: Whenever total magnitude of a force act on a single point then this type of loading on a beam is…

Q: Figure shows a heat exchanger designed to cool 5250 kg/h of an ethyl alcohol solution (Cp = 3810…

A:

Q: What is speed?

A: Speed is a scalar quantity that can give us information about the rate of an object or a body…

Q: Write the SI units of work done.

A: Work is defined as the product of the displacement and the component of force along the…

Q: 7 Doorbe Daanbe the proccdoe lor cvalvahon crnd Cncl improement f laaul. ?

A: Systematic Layout Planning Procedure:- It is a procedure layout design approach developed by Muther…

Q: What about density?

A:

Q: What does shear strains cause?

A: Answer Shear Strain : it is the angular displacement from the original position

Q: What is areal velocity?

A: The measure of the velocity of one celestial body in orbit to another body which is equal to the…

Q: What is the frictional Force

A:

Q: In a machine, the maximum torque transmitted by a shaft exceed by 15 % the actual torque. A power of…

A:

Q: Define the following phrase; i. External forces ii. 111. iv. V. Forces generated by motion Forces…

A:

Q: 15B) Before the object start moving, If applied force is increased, then friction force will a.…

A:

Q: Where did the 0.10472 rad/s come from?

A:

Q: In a hydraulic press machine the diameters of the effort and load pistons are respectively 25 cm and…

A:

Q: What is external force?

A: Answer : Force - It is an effect which changes or try to change the state of a body.

Q: How can I calculate the force tho

A: The stress is defined as the resisting force per unit area. here, σAl=12800 psiσsteel=18850…

Q: 350 lb 30 250 lb

A:

Q: can you Reslove?

A: To solve the problem you have typed in, follow these steps: Analyze the given data:L2 = 6Q2 = 35…

Q: 1. What do you mean by measurement? Why it is needed?

A:

Q: A screwdriver is a kind of wheel and axel machine where the radius of the handle is the input…

A: Given data: The diameter of handle, d1 = 1 in. The diameter of the shaft, d2 = 1/4 in. Write the…

Q: What are the different systems of Units?

A: The different system of units are listed below: SI system MKS system FPS system CGS system The SI…

Q: angular velocity is equal........

A: Angular velocity is equal 2πN60

Q: What is quasistatic compression ?

A: "Quasi-static processes" are ideal reversible processes which cannot occur in practical(real…

Q: What is the unit of surface tension.

A: Unit of surface tension

Q: pascal

A: given: what is pascal law?

Q: -differe nce b etwee

A:

Q: 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

A: Given data 1. 583 mK/s = ________ μK/ms 2. 583 mK/s = _______ K/s

Q: How does the tension in the string change as the masses start to move? Or does it?

A: Consider pulley mass system as shown in the figure below, Scenario 1 Assume the pulley does not…

Q: please, i need to see how did you get to this formula

A: ◆ The purpose of using this formula is to avoid complex calculation and to get the answer in minimum…

Q: Define the term work of force?

A: Work of force is defined as the dot product of force and displacement  W=F.S…

Q: In a lathe machine, The diameter of the driver and driven pulley are 2130 mm and 1590 mm…

A: The ratio of speed of driven pulley to speed of driver pulley is termed as speed ratio for a belt…

Q: 13A) coefficient of friction (H) is O a. normal force + limiting friction O b. normal force limiting…

A:

Q: The direction of the frictional force: O Always opposes the motion or the tendency to motion. O Is…

A: The direction of frictional force has been asked:

Q: The Figure to the right shows a manufacturing process? What is this process called? 2. Identify the…

A: Given :-  1. What is the process called ?

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.