Verify the bending resistance and global stability of the beam. Gravity load is 0.9kN/m, concentrated load 100 kN is applied in the midpoint of the span. Q235 steel is used. a. No brace in the middle of the span. Concentrated load is applied on the top flange. b. No brace in the middle of the span. Concentrated load is applied on the bottom flange. (optional) C. Braced in the middle of the span. Concentrated load is applied on the top flange. d. Same as (a), use Q345B steel. 0.9kN/m 200×12 776x8 200×12 5000 100KN 5000

Verify the bending resistance and global stability of the beam. Gravity load is 0.9kN/m, concentrated load 100 kN is applied in the midpoint of the span. Q235 steel is used. a. No brace in the middle of the span. Concentrated load is applied on the top flange. b. No brace in the middle of the span. Concentrated load is applied on the bottom flange. (optional) C. Braced in the middle of the span. Concentrated load is applied on the top flange. d. Same as (a), use Q345B steel. 0.9kN/m 200×12 776x8 200×12 5000 100KN 5000

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Considering the frame, the height of each storey is 5 m (DA) and 4m (DG) , the length of each span is 6 m (GH) and 7 m (HI), assuming columns and beams have the same cross sectional areas. *Using portal method, what is the axial force at column FC?
Q7/ A precast beam is to be used as a bridge over a small roadway. Concrete dimensions are b= 500 mm, and h = 700 mm. The effective depth d = 600 mm. Concrete and steel strengths are 42 MPa and 420 MPa, respectively. Using approximately one-half the maximum tensile reinforcement permitted by the ACI Code (select the actual size of bar and number to be used), determine the design moment capacity of the girder. If the beam is used on a 9 m simple span, and if in addition to its own weight it must support railings, curbs, and suspended loads totaling 7 kN/m, what uniform service live load limit should be posted?
6-1.2-1: Find lightest W14 for L = 20', P = 600k E = 29,000ksi, Fb = 30ksi and Fv = 20ksi. 30. CONTINUOUS BEAM - TWO EQUAL SPANS-CONCENTRATED LOAD AT CENTER OF ONE SPAN Total Equiv. Uniform Load 13 p 8 P 2 R,= V₁.. 32 R R₂ R₁ R₂= V₁ + V₂. 11 p 16 V₁ R= V₁ V₂ Mmax (at point of load). M. (at support R)..... .......... Amax (at 0.480 / from R.).... M Imax Shear Moment M₁ V₂ ********* ***************** 11 = 11 P 32 - 19 p 32 13 64 = 3. Pl PI 32 0.015 P³ El
6- In simply supported beams, the shear stresses increase when approach to the mid span. O True O False
ASAP PLS THANKS!
The W section is reinforced at top and bottom flanges by a 250 mm wide by 16 mm thick plate is used as a column with with a length of 5.0 m. Determine the safe axial load the column can carry using AISC specifications with Fy = 345 MPa when: a) column ends are fixed b) one end of the column is fixed; the hinged c) both ends are hinged 200 mm CIVIL ENGINEERING STEEL DESIGN tw 13.41 = 8.08mm 250 mm
Prob #l: Design uniform kive load of 22,500 Nm. exclusive of its own weight . Assume the beam to have a simple span of 6m. Use ACI Specs, with fe-20 MPa, f = 138 MPa., 'n=9, Va =0,09| fe and a rectangvlar beam reinforced for tension enly to carry a Va= 22,500 Nm figire : Prob #2: A beam having an 8m. simple span has a cross-section shown in the figure. Defermiìne the maximum concentrated load that this beam can carry besides its own weight. Use fe=7MP., f=124 ME. and n= 10. Figyre: 100 200 100 400mm 100 N.A. --N.A. 600mm 400 5Somm 200mm 550-X 150 n As OSt 4-25mmd Tensicn Bar 400mm
Use NSCP 2015. The beam shown has continuous lateral support of both flanges. The uniform load consisting of 50% dead load and 50% live load. The dead load includes the weight of the beam. Used grade 50 steel. 6 k/ft |--0-0²- -18'-0"- fo 4-6- -6'-0" 1. Considering LRFD. Which of the following most nearly gives the design load Wu? 2. Considering LRFD. Which of the following most nearly gives the maximum negative design moment, Mu in ft-kips? 3. Considering W12x35 beam section, The section is 4. Considering ASD the W12x35 beam section, Which of the following most nearly gives allowable strength in ft-kips
A reinforced concrete simply supported beam has a span of 20 ft and supports service dead load of 2.5 kip/ft and a uniform service live load of 2.5 kip/ft in addition to its self-weight. Design a beam section as per ACI 318-14 to resist the factored external bending moment. The concrete compressive strength at 28 days is(4 + 15)ksi and yielding strength of steel is (60+ 15)ksi.
I need the answer as soon as possible
The frame shown below is subjected to uniformly distributed load of 2.6KP.. Determine the maximum moment of member BF (assume simple beam support) A E, 1.5m F 1.5m 351 C 1.5m H 3m B
Design an angle iron purlin for a roof having a slope of 26° with the horizontal. . The trusses are spaced at 4 m c/c. purlin carries dead load of 4.0 kN/m and wind load 1.5 kN/m pormal to the roof surface. Use IS: 800 specifications. Adopt Ep = 142 MPa for vertical loads and 177.5 MPa for vertical and wind loads combined. The