2. Cantilever Method: The frame shown is subjected to lateral loads as shown. Supports S, T, U V, W and X are rigid supports. Column HMS (400mm x 400 mm) Column ADINT (500 mm x 600 mm) Column BEJOU (600 mm x 600 mm) Column CFKPV (500 mm x 600 mm) Column GLQW (500 mm x 500 mm) Column RX (300mm x 300 mm) Determine the following. a) The shear forces in columns and girders. b) The axial forces in columns and girders. c) The moment at the end of each member. d) Summarize your results by drawing the frame with the internal forces. 5.0 m 5.50 m 6.0 m 7.0 m 120 KN 96 KN (100+SN) KN 144 KN M E O U THE VALUE OF SN IS 34 ROUND OFF THE ANSWER TO 3 DECIMAL PLACES W 5.0 m R XL 4.0m 4.20 m 4.50 m 5.0 m

2. Cantilever Method: The frame shown is subjected to lateral loads as shown. Supports S, T, U V, W and X are rigid supports. Column HMS (400mm x 400 mm) Column ADINT (500 mm x 600 mm) Column BEJOU (600 mm x 600 mm) Column CFKPV (500 mm x 600 mm) Column GLQW (500 mm x 500 mm) Column RX (300mm x 300 mm) Determine the following. a) The shear forces in columns and girders. b) The axial forces in columns and girders. c) The moment at the end of each member. d) Summarize your results by drawing the frame with the internal forces. 5.0 m 5.50 m 6.0 m 7.0 m 120 KN 96 KN (100+SN) KN 144 KN M E O U THE VALUE OF SN IS 34 ROUND OFF THE ANSWER TO 3 DECIMAL PLACES W 5.0 m R XL 4.0m 4.20 m 4.50 m 5.0 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the force in each member of the truss shown by the method of joints. Show free body diagram and handwritten solution. Please make sure it is correct answer. Thank you!
kindly answer this step by step, thank you
Analysis of frames/Zero force identification please show complete solution
4
PLEASE SHOW COMPLETE SOLUTION. THANKS Determine the force in members GE, GC, and BC of the truss shown. Indicate whether the members are in tension or compression. Use method of sections.
Find all member forces and state whether tension or compression (Hand written please )
the frame shown is subjected to lateral loads as shown. Supports S, T, U, V, W, and X are rigid supports. Column HMS Column ADINT - 400*400 Column BEJOU - 500*600 Column CFKPV - 600*600 Column GLQW - 500*600 Column RX - 300*300 Find: a) find the center of gravity(x̄) b) shear(v) and axial forces(p) and moment(m) at each column and girders
The floor structural system shown in Fig 1 comprise W-section steel beams and girders supporting a 5-inch thick concrete slab which provides full restraint to the flanges of the beams. The density of concrete is 150 lbs. /ft³. and the uniformly distributed live load L=50 lbs/ft². L-22¹ B B. Girder G1: - [82] 12' Gl GI [BI] FIG. 1-Steel Floor Beam a) Strength - Bending and Shear 12' + I 1) Produce a sketch of the floor plan showing the tributary load distribution areas for the beams and girders [zul
Determine the force in each member of the truss shown. State whether each member is intension or compression. Use the method of sections. Please find all the forces in each member. Thank you!
A W420x85 steel beam is fully restrained with a uniformly distributed live load of 25 kN/m. The beam has a span of 10m. Use A36 steel. Properties of W40 x 85 A = 10839 mm2 %D bf = 180 mm tf = 18 mm %3D tw = = 11 mm Ix = 310 x 106 mm4 %3D d = 420 mm (Note: Since this is a built-up section, for checking of web slenderness, use h = d - 2t;) %3D 1) Calculate the design shear strength of the section. Check if the section is adequate in shear. USE LRFD and U = 1.2D + 1.6L. %3D 2) Is the maximum deflection at the midspan of the beam due to live load adequate? 3) Calculate the maximum uniform live load that can be carried by the beam.