The floor system shown below supports a uniform dead load of 100 lb/ft² and a uniform live load of 40 lb/ft². Draw the loads with magnitudes on the following structural members: а) BI b) B2 с) ВЗ d) B4 e) Gl f) G2 g) G4 6 @ 7' = 42' C4 B2 B3 2 @ 15' = 30' B) I- G4 G3 G2 BT 5 @ 6' = 30' 36' For the same floor plan shown above and assuming the same floor loads and that the building consists of four floors, determine the following: a) The dead load on column C1 in the first floor. b) The live load on column C2 in the second floor. Consider live load reduction. c) The sum of the dead plus live loads on column C3 in the third floor. Consider live load reduction.

The floor system shown below supports a uniform dead load of 100 lb/ft² and a uniform live load of 40 lb/ft². Draw the loads with magnitudes on the following structural members: а) BI b) B2 с) ВЗ d) B4 e) Gl f) G2 g) G4 6 @ 7' = 42' C4 B2 B3 2 @ 15' = 30' B) I- G4 G3 G2 BT 5 @ 6' = 30' 36' For the same floor plan shown above and assuming the same floor loads and that the building consists of four floors, determine the following: a) The dead load on column C1 in the first floor. b) The live load on column C2 in the second floor. Consider live load reduction. c) The sum of the dead plus live loads on column C3 in the third floor. Consider live load reduction.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

I already solve this question but I got wrong answer(Option A) Correct option is C. Please show me steps to how to get option C.... Please don't give me answer option A. thank you
Need help figuring this out
What is the internal force acting on member DF, EF and EG? Please dictate if its in compression or in tension. Complete solutions please.
Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is inclined I V: 4 H and distance between trusses is equal to 6 m. The purlin has a weight of 79 N/m and spaced at 1.2 m. on centers. The dead load including the roof materials is 720 Pa, live load of 1000 Pa and wind load of 1.2 1.2 1440 Pa. Coefficient of Purlins pressure at leeward and windward are 0.6 and 0.2 respectively. Assume all loads passes through the centroid of the section. Truss Properties of C 200 x 76 mm Sx = 6.19 x 104 mm Sy = 1.38 x 104 mm W = 79 N/m 12 12 1.2 I Allowable bending stress Fbx= Fby = 207 MPa Truss %3D 6m O Calculate the bending stress, fox, for dead load and live load combination (D+ L). Calculate the bending stress, foy, for dead load and live load combination (D + L). O Calculate the maximum ratio of actual to the allowable bending stress for load combination 0.75 (D + L + W) at the windward side. fbx = 151.14 MPa fby = 169.6 MPa Interaction = 1.25
Do not use chat gpt
Establish the dead and live loads for member G3 . Neat fbd please and explanations. The uniformly distributed live load on the floor plane is 100 lb/ft^2
Answer letter b.
Hand written and clean solution please
If beam BEH is hinged at the columns B, E, and H, determine its degree of indeterminacy.
span of beam af is 6 meters. Thank you.
Tributary area Determine the load support by the beams, girders and columns with FBD
ㅏ 2m 2P 2m B Im 4cm 8cm 4cm 4cm 12cm 4cm An overhanging beam is constructed by four wood plates with rectangular cross-section by nails as shown in the figure. If the allowable stresses are oo-10 MPa and t-1 MPa: a) Determine the load P that the beam can carry safely. b) If each nail can support a shear force of Q=2 kN, determine the required nail spacing e using the load P calculated in question (a).