3. The cantilever beam has a T cross section and carries a vertical load at its free end as shown in the figure. At section s-s, find the (a) maximum tensile and compressive stress and (b) maximum shear stress.

Q: The variable section beam has a uniform load w. If it is made of a plate with a constant thickness…

A: A beam of variable depth is given with constant thickness, b. The depth at the support is ho and…

Q: 45KN /m (10KN-m 11OKN. m 135KN 270KN 135KN Gm Gm.

A:

Q: The cantilever beam, whose loading condition and cross-section is given in the figure, is ideal…

A:

Q: (1) The beam is subjected to the shown loading. What is the correct statement regarding the flexural…

A: It is asked to check the nature of flexural stress at point A & B in the beam. For this it is…

Q: A mild steel bar, 1.5 m long, has a square section 40 mm x 40 mm. The bar is subjected to a two-…

A:

Q: In the following figure, the steel plate must support maximum load of P=130 kN. The ultimate shear…

A: Allowable Shear stress =τalτal=Load on each boltALoad on each bolt=P3τal=τFS

Q: Rigid bar ABCD is loaded and supported as shown. Steel [E = 30000 ksi] bars (1) and (2) are…

A:

Q: A beam with a T-section is supported and loaded as shown in the figure. The cross section has width…

A: A beam with the T section is given in the question all the loading condition is given in the above…

Q: Rigid bar ABCD is loaded and supported as shown. Steel [E = 30000 ksi] bars (1) and (2) are…

A:

Q: Compute for the maximum allowable distributed load oo that can be applied to the simply supported…

A:

Q: A mild steel bar, 1.5 m long, has a square section 40 mm x 40 mm. The bar is subjected to a two-…

A: Given- Length L=1.5 m, Square section 40 mm side, Stresses- σx=310 N/mm2,σy=-300 N/mm2,E=2×105…

Q: 200mm 50mm 10 KN 5KNM 200mm 6 m 50mm ) 11.56 MPa O 17.71 MPa ) 21.48 MPa ) 15.6 MPa

A:

Q: As a result of the loading condition given in the I-section fixed beam shown in the figure; a) Find…

A: The given figure is shown below:

Q: Asmall aluminum alloy [E = 74 GPa] tee shape is used as a simply supported beam as shown. For this…

A:

Q: Determine the maximum compressive and tensile bending stresses of the beam shown, cross-section of…

A: Determine the maximum compressive and tensile bending stresses of the beam shown, cross-section of…

Q: A cantilever beam AB, loaded by a uniform load and a concentrated load (see figure), is constructed…

A: In cantilever beam, maximum bending moment always occur at support. So, the maximum Bending moment…

Q: A beam having the cross section shown is subjected to a couple Mo acting in a vertical plane.…

A: Given, Iy = Iz = b436 Iyz = b472 σ = 103 MPa

Q: hat have an outside diameter of 135 mm and a wall thickness of 9 mm. Determine the normal stress in…

A: From a given question it is required to calculate stresses in each member of truss.

Q: 2. Two rods connected as shown carry a vertical load of 20 kN. Rod AB is a steel rod with E = 2 X10³…

A: Given data  EAB = 2 × 105 N/mm2  EBC = 7 × 104 N/mm2  LAB = 3m = 3000 mm  LBC = 2m = 2000 mm  A =…

Q: A laminated plastic beam of square cross section is built up by gluing together three strips, each…

A: Given data, cross section=20 mm x 60 mm The beam has a total weight=4.6 N simply supported with span…

Q: Steel: A- 500 mm "120 MPa P Timber: 4P A 2000 mm 12 MPa Concrete: A- 8000 mm 16 MPa

A: The given data is: Steel column Area = 500 mm2 Working Stress = 120 MPa Timber column Area = 2000…

Q: Find the Stress if Tensile force 2.3 N applied on rod having cross sectional area of 1 mm2

A: Introduction : The question is related with solid mechanics . In this question the data of tensile…

Q: the stresses in bars (1) and (2). the vertical deflection vp of point D on the rigid bar. the load…

A:

Q: 1. Establish stress equations for both bars in the two-bar assembly shown below which isloaded with…

A: The objective of the question is to establish stress equations for both bars in a two-bar assembly…

Q: Calculate the shear stress on a-a plane.

A: Following is the free body diagram:

Q: Jor 6 m 5 kN/m -250 mm 20 mm-

A: Determine the maximum tensile stress in the following beam:

Q: Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are…

A:

Q: A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its…

A: A steel pipe is subjected to the 16-kN load shown below.Outer diameter = 140 mmThickness = 7 mmYield…

Q: A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength…

A: Given:- uniform load=q=200 lb/ft a=12ft b=6ft L=18ft To find:- (a) the maximum tensile stress σt and…

Q: The rigid bar Is pinned at A and held by two flexible bars at E and C. The load P Is appled at B.…

A: Given, Yield stress (σy) = 20 ksi  Yield strain (e) = 0.001

Q: ninum pipes n-connecte that have an outside diameter of 130 mm and a wall thickness of 14 mm.…

A:

Q: 4.15 Knowing that for the casting shown in the figure the allowable stress is 6 ksi in tension and…

A: Allowable stress in tension= 6ksiAllowable stress in compression=15ksiTo find largest couple that…

Q: Steel L = 3 ft A = 0.50 in? E = 29 x 106 psi 2 ft 4 ft

A:

Q: Determine bending stress formula for the I beam

A: The I-section is shown in the figure We need to find a relation to find the bending stress at the…

Q: Q4: For the figure below, determine the principal stresses and show them on a sketch of a properly…

A: We solve this stress condition with mohrs diagram inwhich angle is double of the magnitude of what…

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.