Design column BE as part of an unbraced frame system shown below. Use W12x87 for girders and W14x132 for the column at the other end in determining the effective length coefficient. All structural elements of the frame system will be made up of ASTM A36 steel. Architectural specifications require that the column is to be designed as a rolled W18 section. The column is expected to carry axial compressive load of 100 kN dead load and 300 kN live load. Select the best section that should be used for the said column. For determining effective length factors, neglect inelastic action; and use major axis moment of inertia for girders and minor axis moment of inertia for columns. Use ASD specifications from 2015 NSCP Vol. 1.

Design column BE as part of an unbraced frame system shown below. Use W12x87 for girders and W14x132 for the column at the other end in determining the effective length coefficient. All structural elements of the frame system will be made up of ASTM A36 steel. Architectural specifications require that the column is to be designed as a rolled W18 section. The column is expected to carry axial compressive load of 100 kN dead load and 300 kN live load. Select the best section that should be used for the said column. For determining effective length factors, neglect inelastic action; and use major axis moment of inertia for girders and minor axis moment of inertia for columns. Use ASD specifications from 2015 NSCP Vol. 1.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2.Usingthedoubleintegrationmethod,determinethedisplacementatpointCinthebeamshown.UseE=200GPa.Thesectionisgivenbelowforthemomentofinertia.
Ouestion- Calulote min sD orauirdo ovoiol o heod on Oolli5on Of fwo Cars s oPproching from the opposite drrechin Ot aod Gokmph Assu me t=2.5 Sec f =0-7 Brol1se Efficrendy of 5o in all the Cases. %3D
Find allowablee ) (m) So thut 65+ S140 MP•, 6ü ç lOmpa 50 KN 12 mm 12 kN Y mm 250 mm 下50 150
-([direction]): graphs are given for your basis. kindly provide complete and correct answers. I will like your solution afterward. Thank you!
f=ow06 20M B Lslom Uel 15m Lelon A M/sce [om find Z, , and direction s flow D. LESom
HoW 8-The results Prom lab show that BOD - 205. 5 mglL S-20 find BoD ? BOD ラ a Por Y day 2-32 4-27
مكالمات الطوارئ فقط + If you healthy food, you will * .become slim eat will eat .Tell your brother lunch is ready a the no article الاسم الثلاثي ل لطالب إجابتك محو النموذج إرسال |l> O
TRIANGULATION LINE DISTANCE BEARING CD 20 m S 850 20 E CA N 28º 15 W СВ N 65º 30' E DA N 700 W DB N 80º 15 E 에 에 에
I want to clarify what is that symbol?
3
HELLO PLEASE HELP, WITH COMPLETE SOLUTION. PLEASE DO NOT MAKE IT COMPLICATED THANK YOUU! 4 DECIMAL PLACESS
13 19 81 30 33 3 27 90 5.5 3. 8. 89 69 土1 pom the water furface whereas the 18 24 The deptt usas measured a velociky wap measured woith a prpellv within egch define Creso Sectionof the nver. The efechicead Vefocefies within each panel Cross sectrion and theis Corsespending depths ane shown 'in the table above : 9. Compute the average kpfh and velocity within en ch Panel billsing the single point methsd, Calufate the meas velocubly et the flow wlthin each panel Cross section c. Ufing ether the meay secfion miel-sectisn mgeths Catulhte the avevage elis charge withew each panel Cross section amed thus the toal escharge of the riyen Cros Seefion a depth (ycoed