Variation of the density can be modeled when climbing a mountain as p-887,19*[16-(4z/71)] kg/m. If wind speed at the top of the mountain is = 217 + 127+ 3k m/s, calculate the changing of total density with time [kg/m3.s] at the mountain summit? (NOTE: Take air properties at -10 °C at the top of the mountain. Also, your results must be negative magnitude!!!)

Variation of the density can be modeled when climbing a mountain as p-887,19*[16-(4z/71)] kg/m. If wind speed at the top of the mountain is = 217 + 127+ 3k m/s, calculate the changing of total density with time [kg/m3.s] at the mountain summit? (NOTE: Take air properties at -10 °C at the top of the mountain. Also, your results must be negative magnitude!!!)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

During World War II, Sir Geoffrey Taylor, a British fl uiddynamicist, used dimensional analysis to estimate theenergy released by an atomic bomb explosion. He assumedthat the energy released E , was a function of blast waveradius R , air density ρ, and time t . Arrange these variablesinto a single dimensionless group, which we may term theblast wave number .
The spin rate of a tennis ball determines the aerodynamic forces acting on it. In turn, the spin rate is a§ectedby the aerodynamic torque. If the torque depends on áight speed V , density , viscosity , ball diameter D,angular velocity !, and the fuzz height, hf , Önd the important dimensionless variables for this case. Use V ,, and D as your scaling (repeating) variables.
A football, meant to be thrown at 60 mi/h in sea-level air( ρ = 1.22 kg/m 3 , μ = 1.78 E-5 N . m 2 ), is to be testedusing a one-quarter scale model in a water tunnel ( ρ =998 kg/m 3 , μ = 0.0010 N . s/m 2 ). For dynamic similarity,what is the ratio of prototype force to model force?( a ) 3.86 : 1, ( b ) 16 : 1, ( c ) 32 : 1, ( d ) 56 : 1, ( e ) 64 : 1
Engine oil at 40 C [density 876 kg/m^3, viscosity 0.2177 kg/m.s] flows in a 20-cm-diameter pipe at a velocity of 0.9 m/s. The pressure drop (in Pa) of oil for a pipe length of 20 m is
1. (a) The motion of a floating vessel through the surrounding fluid results in a drag force D which is thought to depend upon the vessel's speed v, its length I, the density p and dynamic viscosity μ of the fluid and the acceleration due to gravity g. Show that:- D = pv²1² (1) (b) In order to predict the drag on a full scale 50m long ship traveling at 7m/s in sea water at 5°C of density 1027.7225 kg/m³ and viscosity 1.62 x 103 Pa.s, a model 3m long is tested in a liquid of density 805 kg/m³. What speed does the model need to be tested at and what is the required viscosity of the liquid?
2 A prototype car is designed for cold weather operation in Denver (-10°C, 83 kPa, altitude 1600m, µ = 1.741 × 10-5 Pas). It's drag force is to be tested in a 1:7 model in a wind tunnel at 150 mph under standard sea level conditions. If the model and prototype satisfy dynamic similarity what prototype velocity, in mph, is matched? Is this a reasonable test? 1 mile = 1609 m HINT: p = pRT
For a venturi meter given below, the volumetric flow rate is defined in terms of the geometrical parameters, the density of working fluid (p), and density of the manometer liquid (pm) as 4. Q = f(D, D2, A2, g, h, Pmv Pr) %3D Write down the balance equations and show your work to end up with an expression for the volumetric flow rate in terms of the variables defined above.
: You are abducted by aliens and find yourself locked in a large room on some strangeplanet. To pass the time, you decide to do some experiments using a ball-and-chain thatyou find on the floor. You make the following estimates:mBALL  7 kg ,mCHAIN  0.5 kg, and CHAIN  2 m .(a) When you hold the free end of the chain above your head and allow the ball to swinglike a pendulum, you use your wristwatch to measure the period asT  4 s. What is theacceleration due to gravity on this planet?(b) If the ball accidentally hits a wall, how long does it take for this jolt in the chain totravel up to your hand?
In the given image, both fluids are at 20°C. The specific weight of water is 9790 N/m³. If surface tension effects are negligible and a = 8.35 cm, what is the density of the oil, in kg/m³? Oil 6 cm Water Numeric Response CO 10 cm
Buckingham Pi. A mechanical stirrer is used to mix chemicals in a large tank. The required shaft power P is a function of liquid density p, viscosity μ, stirrer blade diameter D, and angular speed w of the spinning blades. (a) use repeating variables p, D, u to find a relation between dimensionless power (1) and w (m2); (b,c) a small 1/3 scale model is used in water to predict the actual required power in a viscous liquid with SG =2 and μ = 12μwater. Find (b) the ratio of speeds, wwater/ wactual, necessary for dynamic similarity and then (c) the predicted ratio of powers Pwater/ Pactual. expecting unit : (a) π1 ~ D ; π^2 ~ D^2; (b) wwater/ wactual: 10^0; (c) Pwater/ Pactual 10^-3 SI constant Patm = 10^5 Pa; pwater - 1000 kg/m^3; pair ~ 1.2kg/m^3; µwater ~ 10^-3 N•s/m^2; pair - 2 x 10^-5 N•s/m^2 ; g = 9.8 m/s^2 =
There are many common dimensionless numbers used to describedifferent physical effects. Such dimensionless numbers are usually a ratioof specific properties, for example, the Reynolds number represents theratio of inertial to viscous forces.Choose three of the following dimensionless numbers and describe whatproperties the ratio represents and the context in which these numbers areimportant: Froude Number, Euler Number, Mach Number, Weber Number,Nusselt Number, Prandtl Number.
Consider the pressure Drop depends on: @ characterstic lugth I 2 density ℗ gravity g speed of sound с angular velocity w surface tension Velocity of fluid V Viscosity of fluid write an expression of the pressu drop ?