In this lab we will drop a steel ball (Psteel = 8000 kg/m³, rball = 2.18 x103 m) through the air (Nair = 1.8 x10 Pa.s, Pair = 1.29 kg/m³), and through a viscous soap solution (nsoap = 9.0 Pa.s [you will measure this number in the lab, but use this number for the prelab], Psoap = 1000 kg/m³). %3D 1 Pa = 1 N/m?. Calculate the terminal speed of the ball falling through the air, assuming that inertial drag is the dominant contributor. (For a sphere CD = and A is the area of the circle of radius r of the ball). Neglecting drag, estimate the time in seconds it takes for the steel ball to reach the terminal speed found in part 2 (1). Neglecting drag, estimate how far the ball would have travelled before reaching its terminal speed and comment on whether it is reasonable to neglect drag when studying the motion of this ball as it falls through the air from rest from the top of a 30 cm tall beaker or even from the ceiling of the room. O Neglecting drag it would take 36 m to reach the terminal velocity. Since a room is about 1/12 of this distance it is a good approximation to neglect drag even when dropping the steel ball from the ceiling of the room through the air.

In this lab we will drop a steel ball (Psteel = 8000 kg/m³, rball = 2.18 x103 m) through the air (Nair = 1.8 x10 Pa.s, Pair = 1.29 kg/m³), and through a viscous soap solution (nsoap = 9.0 Pa.s [you will measure this number in the lab, but use this number for the prelab], Psoap = 1000 kg/m³). %3D 1 Pa = 1 N/m?. Calculate the terminal speed of the ball falling through the air, assuming that inertial drag is the dominant contributor. (For a sphere CD = and A is the area of the circle of radius r of the ball). Neglecting drag, estimate the time in seconds it takes for the steel ball to reach the terminal speed found in part 2 (1). Neglecting drag, estimate how far the ball would have travelled before reaching its terminal speed and comment on whether it is reasonable to neglect drag when studying the motion of this ball as it falls through the air from rest from the top of a 30 cm tall beaker or even from the ceiling of the room. O Neglecting drag it would take 36 m to reach the terminal velocity. Since a room is about 1/12 of this distance it is a good approximation to neglect drag even when dropping the steel ball from the ceiling of the room through the air.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Saturated steam at 99.6 °C is heated to 350°C. Use the steam table provided to determine: a. The required heat input if 1 kg of steam undergoes the process in a variable-volume constant-pressure container. b. The work of expansion (in kJ) of the steam undergoing the process. C. The required heat input if a continuous stream flowing at 1 kg/s undergoes the process at constant pressure. d. Does your numeric answer to part c equal the sum of parts b and a? Explain why or why not. Given: 1 bar = 10 N/m4, Q= AH, Q = AU, AA = AÛ + PAV, table B.7 in kJ/kg and m/kg.
Q2:A) An experimental text program is being set up to calibrate a new flow meter. The flow meter is to measure the mass flow rate of liquid flowing through a pipe. It is assume the mass flow rate (m) is a function of the pressure difference (AP)across the meter, diameter of the pipe (D), viscosity of the fluid (4), and the density of the fluid (p). Using the dimensionless analysis, find the-groups for this case study.
A2) In order to solve the dimensional analysis problem involving shallow water waves as in Figure 2, Buckingham Pi Theorem has been used. h Figure 2 Through the observation that has been done, the wave speed © of waves on the surface of a liquid is a function of the depth (h), gravitational acceleration (g), fluid density (p), and fluid viscosity (µ). By using this Buckingham Pi Theorem: a) Analyze the above problem and show that the Froude Number (Fr) and Reynolds Number (Re) are the relevant dimensionless parameters involve in this problem. b) Manipulate your Pi (1) products to get the parameter into the following form: pch := f(Re) where Re = Fr = c) If one additional primary variable parameter involve in this proolem such as, temperature (T). Discuss on the Pi (m) products that can be produce and explain why this dimensional analysis is very important in the experimental work.
9. A water Reservoir 80m 40m f 0.005 d = 0.2m Datum C D Turbine/generator Data: v in pipe = 3 m/s v at D = 0 Pressure at D = 0 Turbine efficiency = 80% Generator efficiency = 90% a). Pressure at C[+351.5 kN/m²] b). Output power from generator [24.16 kW] Determine:
5. Consider a Pitot probe in high-speed flow.(c) You are flying through air at static p∞ = 0.8 atm [abs]. Your velocimeter broke,but you are still receiving the following direct stagnation pressure readings (atm[abs]) from the Pitot probe mounted on your aircraft’s noise: i) 3.152 ii) 1.357 iii) 38.428 iv) 0.8 Find the freestream Mach number corresponding to each of the pressure readings. (d) If we are to believe reading (iv), can we step out of the aircraft safely? Why?
Taylor number (Ta) is used here to describe the ratio between the inertia effect andthe viscous effect. By applying Buckingham Pi’s Theorem, determine an equation forTa as a function of the radius of inner cylinder (r), cylinder tangential velocity (v),fluid dynamic viscosity (μ), gap distance (L) and fluid density (ρ).
To understand the heat transfer from a bar in cross flow, you conduct a series of experiments measuring the average heat transfer coefficient as a function of the free stream velocity. A schematic of the experiment and the accompanying results are shown below. L = 0.3 m h [W/m²-K] 60 40 V [m/s] 20 15 a) You expect the important dimensionless parameters to be related by a function of the form Nu = CRe Pr where C, m, and n are constants. The film temperature in both the experiments is approximately the same. Use the given experimental results to determine the constant m b) Calculate h for L = 0.75 m and V = 30 m/s.
I need the answer as soon as possible
> | E9 docs.google.com/form تبديل الحساب Questions 7 نقاط Q1/ The power of 6-blade flat blade turbine agitator in a tank is a function of diameter of impeller, number of rotations of the impeller per unit time, viscosity and density of liquid. From a dimensional analysis, obtain a relation between the power and the four variables. 3. صفحة 2 من
I need the answer as soon as possible
Please try to solve in 1 hour
Fill in blank hell