2 A prototype car is designed for cold weather operation in Denver (-10°C, 83 kPa, altitude 1600m, µ = 1.741 × 10−5 Pas). It's drag force is to be tested in a 1: 7 model in a wind tunnel at 150 mph under standard sea level conditions. If the model and prototype satisfy dynamic similarity what prototype velocity, in mph, is matched? Is this a reasonable test? 1 mile = 1609 m

2 A prototype car is designed for cold weather operation in Denver (-10°C, 83 kPa, altitude 1600m, µ = 1.741 × 10−5 Pas). It's drag force is to be tested in a 1: 7 model in a wind tunnel at 150 mph under standard sea level conditions. If the model and prototype satisfy dynamic similarity what prototype velocity, in mph, is matched? Is this a reasonable test? 1 mile = 1609 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The aerodynamic drag of a new sports car is to be predicted at a speed of 60.0 mi/h at an air temperature of 25°C. Automotive engineers build a one-third scale model of the car to test in a wind tunnel. The temperature of the wind tunnel air is also 25°C. The drag force is measured with a drag balance, and the moving belt is used to simulate the moving ground (from the car’s frame of reference). Determine how fast the engineers should run the wind tunnel to achieve similarity between the model and the prototype.
Fast pls
A light parachute for military purposes is being designed. Its diameter is 7.3 m, test load, parachute and rig weight is 1023 N. For this weight, the limit descent speed Vt = 6.1 m / s, which is taken as a basis in the design of the parachute. The 1/12 scale model will be tested in the wind tunnel and the temperature and pressure of the tunnel are the same as that of the prototype. (15.5 ºC and standard atmospheric pressure) a) Calculate the resistance coefficient of the prototype. (Hint: At the limit descent speed, the weight is balanced by the aerodynamic resistance.) b) At what speed should the wind tunnel be run to achieve dynamic similarity? c) Calculate the aerodynamic resistance of the model parachute in the wind tunnel. Density of air at 15.5 ºC and standard atmospheric pressure ρ = 1.22 kg / m3 viscosity, µ = 8.16x10-6 kg / m.s will be taken.
Please solve correctly with explanation.
A uniform stream overflows in a circular cylinder and then a periodic Kármán vortex street is created. Through repeating variables, how can I create a dimensionless relationship for Kármán vortex shedding frequency (fk), where free-stream speed is V, fluid density is p, fluid viscosity is μ, and cylinder's diameter is d?
Solve it correctly
Step by step work starting with the formula.
1. (a) The motion of a floating vessel through the surrounding fluid results in a drag force D which is thought to depend upon the vessel's speed v, its length I, the density p and dynamic viscosity μ of the fluid and the acceleration due to gravity g. Show that:- D = pv²1² (1) (b) In order to predict the drag on a full scale 50m long ship traveling at 7m/s in sea water at 5°C of density 1027.7225 kg/m³ and viscosity 1.62 x 103 Pa.s, a model 3m long is tested in a liquid of density 805 kg/m³. What speed does the model need to be tested at and what is the required viscosity of the liquid?
1. A model submarine is tested in a sea water tank at a speed of 30 m/s. The prototype speed should be 21.6 km/hr. (a) Determine the geometric scale between the model and the prototype (b) Determine the model speed if it is tested in a pressurized air wind tunnel with 12/s. kinematic viscosity v = 8 × 10-7 m² /s. For sea water use v = 1.124 × 10-6 m² /s.
The drag on a 2-m-diameter satellite dish due to an 69-km/hr wind is to be determined through a wind tunnel test using a geometrically similar 0.4-m-diameter model dish. Assume standard air for both model and prototype. (a) At what air speed should the model test be run? (b) With all similarity conditions satisfied, the measured drag on the model was determined to be 152 N. What is the predicted drag on the prototype dish? (a) Vm = (b) D = i i km/hr N
Air flows across a thin airfoil at a velocity of 90 m/s. For the same Reynolds number based on the actual chord length, L = 1.40 m, what velocity of water is required for a 1/2 scale model test? Assume a temperature of 15°C for both fluids. air U = 90 m/s L = 1.40 m