v Part 1 For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=9.5 ft, b=20.0 ft, P = 45 kips and w = 10.0 kips/ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. В Calculate the reaction forces A, and C, acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since A, = 0, it has been omitted from the free- body diagram.) b. Answers: A, = kips Cy = kips

v Part 1 For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=9.5 ft, b=20.0 ft, P = 45 kips and w = 10.0 kips/ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. В Calculate the reaction forces A, and C, acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since A, = 0, it has been omitted from the free- body diagram.) b. Answers: A, = kips Cy = kips

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

For those who knows Engineering Mechanics. Can someone help me to solve the problem below. I will surely upvote for your answer. Need answer ASAP. Thanks
Question 2. The figure below shows a hollow circular beam with an outside diameter of 250 mm and a wall thickness of 20 mm loaded in bending with force F = 50 kN. F Ra I: Young's modulus of the beam is 60 GPa.. Calculate the second moment of area, I, in m4 in the form ax 106 where the number a is correct to two decimal places. M: 1 m x 10 m4 Calculate the maximum bending moment, M, in kilonewtonmetres (kNm): σ: kNm E: 1 m Calculate the maximum bending stress, o, in megapascals (MPa) correct to two decimal places. Rb MPa Hence, calculate the maximum compressive strain, e, Enter your answer in micro-strain correct to two decimal places: micro-strain Type here to search 91 DELL 80°F
Solve it correctly please.
50 kN *** w 1* 4 m 3 kN/m 5 75 kN 37° Draw the shear force diagram and the bending moment diagram for the anchor beam below.
please answer it with ; given, solution, diagrams/ drawing, answer please expain part by part
i dont think these answers are right. please answer!!!
Find the Nominal force, N in kilo Newtons (kN). What is the shear force, V in kilo Newtons (kN). Find the bending moment, M in kilo Newton metres (kNm).
Use the graphical method to construct the bending-moment diagram and identify the magnitude of the largest moment (consider both positive and negative). The ground reactions and the shear-force diagram are provided. M = 13 kN-m Ay = 3.46 KN Dy Units: KN = 32.54 kN M 4 m 29.5 kN-m 43.3 kN-m 25.8 kN-m O 22.9 kN-m 31.48 kN-m B Ay 4 m 15 kN C Ay 4 m Ay-15 7 kN/m D 3 m 21 Ay-15 E X
Please solve very soon completely
The cantilever beam is loaded as shown in the figure. Derive the equations for the shear force (V) and the bending moment (M) for any location in the beam. Analyze the beam from the left, taking point A as the origin. 4 kips/ft 8 ft 8ft What is the moment (in kips-ft) at x = 4.00 ft? What is the shear force (in kips) at x = 5.50 ft? What is the moment (in kips-ft) at x = 13.00 ft? What is the behavior of V equation between points B and C? What is the behavior of M-diagram between points B and C?
A storage rack to hold the paper roll. Find force reactions and draw the shear and moment diagrams for the mandrel that extends half of the roll. Use singularity functions for this problem. Givens stanchion paper roll Density=984 kg/m^-3 OD=1.5 m ID=0.22 m L=3.23 m Density=mass/volume So W=(density*volume)*gravity Volume of hollow cylinder= (pi/4)(OD^2-ID^2)*Length of cylinder Length of mandrel=1/2 of L=>1.615 m mandrel base Assumptions: The storage rack is acting with a fixed support With a distributed load of "w" where w is the weight distrubuted
Im doing a shear and moment calculation for a problem graphically and keep getting a negative sign in my moment calculation where I should be getting a postive sign. I know that the integral of my shear calculation is going to be my moment equation but I always use this to "check" myself against my work after I do my standard summation of moments about a point. I KNOW I SHOULD be getting M_2(x) = -.5x^2 + 2x + c but as you can see by my work I keep getting a "-2x". Why is this and where am I going wrong?