Part B - Normal and shear stress on element sectioned at plane b-bUsing the element sectioned at plane b-b and the rotated coordinate system shown, determine the normal and shear stresses acting on plane b-b.eExpress your answers in ksi to three significant figures separated by a comma.15. ΑΣΦ | 11 | vecOF TEV?ksi Learning Goal:To use fundamental geometric and statics methods to determine the state of plane stress at the point on an element of material that is rotated clockwise through an angle from the in-plane stress representation of the point.The state of in-plane stress at a point on an element of material is shown. Let o,the same point that is rotated through an angle of 0-3545.0 ksi, o, 19.0 ksi, and Ty 12.0 kai. Use this information to represent the state of stress of

Answered: Image /qna-images/answer/16c7e71e-98b9-46b8-b4f0-1593787a55c1.jpg

Using the element sectioned at plane b-b and the rotated coordinate system shown, determine the normal and shear stresses acting on plane b-b. Express your answers in ksi to three significant figures separated by a comma. 195] ΑΣΦ. it Ivec JETEV ? ksi

Using the element sectioned at plane b-b and the rotated coordinate system shown, determine the normal and shear stresses acting on plane b-b. Express your answers in ksi to three significant figures separated by a comma. 195] ΑΣΦ. it Ivec JETEV ? ksi

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Several forces are applied to the pipe assembly shown. Knowing that Q=250 lb and that the pipe has…

Q: For the given state of plane strain, use Mohr's circle to determine the state of plane strain…

Q: At a point on a structural member subjected to plane stress, normal and shear stresses exist on…

Q: Forces are applied at points A and B of the solid cast-iron bracket shown. The bracket has a…

Q: The state of stress at a point in a member is shown on the element in Figure 6. Determine the stress…

A: Write the given information:

Q: etermine the absolute maximum shear stress.

A: Given that , σxx=-79.7 MPaσyy=50.5 MPaτxy=-24.9 MPa

Q: The square deforms into the position shown by the dashed lines in. The dimensions are S=49 mm, S′=54…

A: Given data- S=49 mm, S′=54 mm, Δx1=5 mm, and Δx2=9 mmDetermine-A) the shear strain at A relative to…

Q: Select the appropriate Stress -Strain plot which is the most ductile from the following graph

A: In stress-strain diagram, x increases => More ductility y increases => More strength Area…

Q: The 0.91-in.-diameter rod in (Figure 1) is subjected to the loads shown. Figure 9 in. 200 lb 300 lb…

Q: at each of those points. Write each state of stress in the form of a tensor, observing the z-y-…

Q: B) The Figure shows Mohr's circle for a point in a physical object that is subjected to plane…

Q: Determine stress components acting on the inclined plane AB shown in Figure 1. The directions of the…

A: Given: The stress in x-direction, σx = -70 MPa The stress in y-direction, σy = 50 MPa The shear…

Q: a. Use Mohr's Circle to determine the maximum shear stress on the element b. Also, using Mohr's…

A: Mohr's circle for, σx=-30MPaσy= 50MPaτxy= 20MPa

Q: The stresses shown on the right below act at a point on the surface of a cantilever beam, as shown…

A: Principal stress is defined as the maximum or minimum value of normal stresses and they act on that…

Concept explainers

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.

Question

Part B - Normal and shear stress on element sectioned at plane b-b
Using the element sectioned at plane b-b and the rotated coordinate system shown, determine the normal and shear stresses acting on plane b-b.
e
Express your answers in ksi to three significant figures separated by a comma.
15. ΑΣΦ | 11 | vec
OF TEV
?
ksi

Learning Goal:
To use fundamental geometric and statics methods to determine the state of plane stress at the point on an element of material that is rotated clockwise through an angle from the in-
plane stress representation of the point.
The state of in-plane stress at a point on an element of material is shown. Let o,
the same point that is rotated through an angle of 0-35
45.0 ksi, o, 19.0 ksi, and Ty 12.0 kai. Use this information to represent the state of stress of

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

5. consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Determine the principal stresses acting at the point. Show these stresses on an appropriate sketch 66 MPa 114 MPa 90 MPa
The state of in-plane stress at a point on an element of material is shown. Let |σx| = 370 MPa, |σy| = 130 MPa, and |τxy| = 85.0 MPa. Use this information to represent the state of stress of the same point that is rotated through an angle of θ = 25.0.
Mohr's cirde is shown for a point in a physical object that is subjected to plane stress. Each grid square is 24 MPa in size (a) Determine the stresses 0, 0, and the magnitude of Ty and show them on a stress element (b) Determine the principal stresses and the magnitude of the maximum in-plane shear stress acting at the point and show these stresses on an appropriate sketch (eg, see Figure 12.15 or Figure 1216).
Solve the problem using the stress transformation equations. Suppose that σx= 92 MPa, σy= 46 MPa, τxy= 36 MPa in the directions shown. A) Determine the normal stress component acting on the plane AB. B) Determine the shear stress component acting on the plane AB.
answer this ; The vertical coordinate (y-coordinate; the y-axis serves as the axis of symmetry of the cross-section.) and horizontal coordinate (z-coordinate) of the location where the maximum shear stress occurs in the section are y= mm ; z= mm; The vertical distance from the location where the maximum shear stress occurs in the section to the bottom side ( AB ) of the cross section can be calculated as Distance = mm
A force Q of magnitude 3 kips is applied to the machine element AB as shown. The uniform thickness of the element is 0.8 in. -8 in. -8 in. 35° 8 in. B 1.5 in. 1.5 in. Determine the normal and shearing stresses at point a. The normal stress is ksi. The shearing stress is ksi.
Determine the state of stress at point q. The pipe has an inner diameter of D₁ = 1.0 in and an outer diameter of = 1.8 in. Use the exact expression for Q, if needed. Label the reultant forces on the cross section below. Report your answer (3x3 matrix) in psi to one decimal place. Do 4 in. Y 4 in. 150 lb 6 in. 50 lb 10 in. 200 lb 150 lb X N Y
Do not answer in image format
The state of plane stress at a point is shown on an infinitesimal element below. Determine the stresses at the point on an element that is oriented 65° counter-clockwise from the x, y axes shown. Enter the shear stress on this rotated element Ta'y' (with correct magnitude and sign) in kPa correct to 3 significant digits below. 300 kPa y 400 kPa X 400 kPa 300 kPa
Determine the normal and shear stresses at point D that act perpendicular and parallel, respectively, to the grains. The grains at this point make an angle of 30° with the horizontal as shown. Point D is located just to the left of the 10-kN force
Please find the question attached.
Determine the equivalent state of stress if an element is oriented 20° clockwise from the element shown in Figure 1. σχ, σγ' and τχγ 2 MPa 3 МРа 4 MPa