5. consider a point in a structural member that is subjected to plane stress. Normal and shearstresses acting on horizontal and vertical planes at the point are shown. Determine the principalstresses acting at the point. Show these stresses on an appropriate sketch66 MPa114 MPa90 MPa

if you have any doubt please comment

Answered: 5. consider a point in a structural…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the equivalent state of stress on an element at the same point oriented 60° counterclockwise with respect to the element shown. Sketch the results on the element
1) The state of stress on an element is shown in following figure. i) Determine the stresses acting on an element oriented at a counterclockwise angle of 48° from the horizontal. Show these stresses on a properly oriented element. ii) Determine the principal stresses and the principal angle. Show these stresses on a properly oriented element. iii) Determine the maximum shear stress, angle for maximum shear stress and normal stresses when maximum shear stress exists. Show these stresses on a properly oriented element. 140 MPa A 42 MPa 60 MPa
A 6 meter cable is attached to two points of the same elevation on the ceiling room. The two points are three meters apart. A 100N is tied to the center of cable. Determine the stresses in Pascals of each cable if their cross sectional area is equal to 5 mm^2
The principal strains at a point on the aluminum surface of a tank are P1 = 630(10-6) and P2 = 350(10-6). If this is a case of plane stress, determine the associated principal stresses at the point in the same plane. Eal = 10(103) ksi,nal = 0.33.
Determine normal stress.
1. Determine the equivalent state of stress on an element at the point which represents, the principal stresses and, the maximum in-plane shear stress and the associated average normal stress. Also, determine the corresponding orientations of the element. a. Use Equation Method b. Use Mohr's Circle 28 MPa 14 MPa 7 MPa
Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid square is 1 MPa in size. (a) Determine the stresses o, o, and the magnitude of Tyand show them on a stress element. (b) Determine the stresses o,, Og and the magnitude of Tht and show them on a stress element that is properly rotated with respect to thex-y element. The sketch must include the magnitude of the angle between thexand n axes and an indication of the rotation direction (i.e., either clockwise or counterclockwise). Answer: (a) Ox= MPа MPa Oy= MPa Txy = (b) On= MPa MPa Ot = MPa Tnt =

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

5. consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Determine the principal stresses acting at the point. Show these stresses on an appropriate sketch 66 MPa 114 MPa 90 MPa