Use Virtual Work Method to answer the questions below considering the truss shown in the figure. Assume A = 1200 mm?, E = 200 GPa and a = 12 x 10° / °C a. Axial force on member ED from the real structure in kN. Put (-) negative sign if it's under compression. b. Axial force on member AE from the wirtual structure for the vertical displacement at joint A. to E 4.1m A B 3.6 kN 5.4 kN 4.1m 4.1m

Use Virtual Work Method to answer the questions below considering the truss shown in the figure. Assume A = 1200 mm?, E = 200 GPa and a = 12 x 10° / °C a. Axial force on member ED from the real structure in kN. Put (-) negative sign if it's under compression. b. Axial force on member AE from the wirtual structure for the vertical displacement at joint A. to E 4.1m A B 3.6 kN 5.4 kN 4.1m 4.1m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

9 Consider the plane truss with load Pas shown in the figure. Let the horizontal and vertical reactions at the joint B be Hg and V, respectively and Vc be vertical reaction at the joint C. 2 exhoM S SLO 60° - II B A 60° D L 60° F 60° KLA G P с Which one of the following sets gives the correct values of VB, HB and V? (a) VB = 0; HB = 0; Vc = P (b) VB P/2; HB = 0; Vc = P/2 (c) VB = P/2; HB = P (sin60°); Vc = P/2 (d) VB = P; HB = P (cos(60°); Vc = 0 [2016
The rigid bar ABC shown is hinged at A and supported by a steel rod at B. Determine the load P that can be applied at C if the stress in the steel rod is limited to 37 ksi and the vertical movement of end C must not exceed 0.1 in. Let a = 3 ft. and b = 2 ft. Consider only the load based on the deformation at C. Answer must be in kips. Steel L= 4 ft A = 0.50 in? E = 29 x 10° psi a ft. b ft.
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm^2; link CD is made of steel (E = 200 GPa) and has a cross-sectional area of 600 mm^2. For the 30 kN force shown, determine the deflection of B and E, respectively. 0.4 m 0.3 m B A 0.2 m OC -0.4 m 30 kN E
1. Use stiffness matrix to compute reactions at boundaries and element force considering the following conditions: EA = 5000 kN m (1). Horizontal force = 10 kN at point D rightward and vertical force =50 kN at point C downward. (2). Without external force, element 5 is 0.01 m too long. 4 m A (2) 2 D 3 m (O 6 (5) (4) 1 B (3) с Truss Numbers in red color refer to the degrees of freedom
Consider the distributed loading acting on the frame structure which is pin-supported at B and D:a. Calculate a the free coefficient in the distributed load function w(y). Make sure to provide its proper units as well.b. Calculate the resultant force from the distributed load and where it acts along member AB. c. Show a complete and labeled free-body diagram(s) of the structure with the distributed lod replaced by a single concentrated force.d. Solve for the support reactioncomponents Bx, By, Dx, Dy on the frame at the pin-support locations B and D.
9 Consider the plane truss with load Pas shown in the figure. Let the horizontal and vertical reactions at the joint B be Hg and V, respectively and Vc be vertical reaction at the joint C. 2 exhoM S SLO 60° - II B A 60° D L 60° F 60° KLA G P с Which one of the following sets gives the correct values of VB, HB and V? (a) VB = 0; HB = 0; Vc = P (b) VB P/2; HB = 0; Vc = P/2 (c) VB = P/2; HB = P (sin60°); Vc = P/2 (d) VB = P; HB = P (cos(60°); Vc = 0 [2016
L/2 The planar structure RST shown in the figure is roller-supported at S and pin-supported at R. Members RS and ST has uniform flexural rigidity (El) and S is a rigid joint. Consider only bending deformation and neglect effects of self-weight and axial stiffening. R. When the structure is subjected to a concentrated horizontal load P at the end T, the magnitude of rotation at the support R, is
Figure 1 shows a pin-connected truss system with pin supports at points A and B. Member AC has an area of 60 mm², E= 200 GPa, and yield stress oy= 150 MPa; Member BC has an area of 35 mm², E= 200 GPa, and yield stress oy= 200 MPa. A force is applied horizontally at point C as shown in the figure, with corresponding displacement A. Draw the complete F versus A response up to collapse and calculate the over-strength of the system. A B mom топп 60° 2 m F, A C
Determine the support reactions and joint forces on the compound beam in the figure. There is a hinge at point B
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider the figure shown with P= 137 kN. 2.4 m 2.4 m 2.4 m TO B O 4.5 m E Determine the force in members DG and EG of the truss shown. KN Tension The force in member DG of the truss is The force in member EG of the truss is [ KN Tension :
QUESTION 2 Determine the force in member CD using method of section of the truss shown if: P= 522 Kn Q= 693 Kn N= 301 Kn M= 242 Kn Use 2 Decimal places. If the member is in compression you need to include the negative (-) sign in your inputted answer. Do not include the unit in inputting your answer. P 6 m 3 m 3 m 6 m 6 m M
Q2 / The cross sectional area of each member of the truss as shown in the figure below 1.75 in and E = 29(10')ksi , determine the vertical displacement at joint D due to radiant heating of member FD is subjected to an increase in temperature from 20° F C to 110° F, take a = 0.75(10³)/F , and member CD would be decreased 0.2 in use Method of Virtual Work. (P in k) P=9 VP F E 4 m А D B C 3 m 3 m 3 m +