The truss is subjected to the system of forces as shown in the following figure. The truss is supported by a pin at A and a pin at E. If P1 P2 = 4 kN, the force in member (CB) is equal to. %3D 30° 30° C E D 3 m 3 m P1 P2 Select one: a. 4.618 kN - Tension b. 8 kN - Compression c. 2 kN - Tension d. 8 kN - Tension

The truss is subjected to the system of forces as shown in the following figure. The truss is supported by a pin at A and a pin at E. If P1 P2 = 4 kN, the force in member (CB) is equal to. %3D 30° 30° C E D 3 m 3 m P1 P2 Select one: a. 4.618 kN - Tension b. 8 kN - Compression c. 2 kN - Tension d. 8 kN - Tension

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

From the given truss shown, FA = 150, FB = 200, and FC = 250 N. Compute the following. Specify whether the forces in each member are in tension or compression. a. find the reaction at C b. find the force in member AC c. find the force in member CD d. find the force in member AD
The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a factor of safety F.S. = 2.0 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. B A 1.5 kn/m 10m Figure 3.1 Suspended Floor Beam D C
The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a factor of safety F.S. = 2.0 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. B A 1.5 kn/m 10m Figure 3.1 Suspended Floor Beam D C
CF-GH
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 109 GPa] with a cross-sectional area of A₁ = 530 mm². Bar (2) is an aluminum alloy [E = 64 GPa] with a cross-sectional area of A2 = 330 mm². A concentrated load of P = 67 kN acts on the structure at D. Assume L₁=740 mm., L₂=500 mm., a=660 mm., b=310 mm., and c=1030 mm. Determine: (a) the normal stresses 0₁, 02 in both bars (1) and (2). (b) the downward deflection VD of point D on the rigid bar.
Asap please
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 116 GPa] with a cross-sectional area of A₁ = 550 mm². Bar (2) is an aluminum alloy [E = 71 GPa] with a cross-sectional area of A₂ = 290 mm². A concentrated load of P = 62 kN acts on the structure at D. Assume L₁=800 mm., L2=560 mm., a-590 mm., b=430 mm., and c=1160 mm. Determine: (a) the normal stresses 01, 02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. a b Answers: (a) σ₁ = (b) VD = i (1) L₁ L2 (2) A B MPa, 0₂ = mm. D MPa
The rods AB and CD are made of steel having a failure tensile stress of ?FAIL = 500MPa. Using a factor of safety F.S. = 2.0 for tension, determine their smallest diameter so that they can support the load shown. The beam is assumed to be pin connected at A and C. B A 1.5 kn/m 10m Figure 3.1 Suspended Floor Beam D C
The truss is loaded by concentrated forces as shown in the figure. Use E = 30 x 106 psi and A = 0.90 in² for all the members. Determine the deformation sustained by members CG and FG. 12 kips 14 kips 16 kips A B с 10 kips |-6R-|-6A 8 ft ļE 5 ft ——6 ft—6 ft--6 ft-
Problem 2: Determine the force in ALL the members of the truss. State if the members are in tension or compression. Show all your work to receive full credit. (Hint: It is not needed to find the reaction forces at C and E if you use the Method of Joints). Note: P1= 1000 lb and P: = 500 lb B C30 45 999 4 ft E 550 D. -4 ft- - 4 ft- 999 299