The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm^2; link CD is made of steel (E = 200 GPa) and has a cross-sectional area of 600 mm^2. For the 30 kN force shown, determine the deflection of B and E, respectively. 0.4 m 0.3 m B A 0.2 m OC -0.4 m 30 kN E

The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm^2; link CD is made of steel (E = 200 GPa) and has a cross-sectional area of 600 mm^2. For the 30 kN force shown, determine the deflection of B and E, respectively. 0.4 m 0.3 m B A 0.2 m OC -0.4 m 30 kN E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The rigid bar BDE is supported by two links All and CD. Lank All is made of steel (E200 GPa) and has…

Q: Please explain all question and draw diagram

A: Part 1. Calculate the displacements at the jointsGiven InformationThe truss structure is square with…

Q: Please show me how to solve this with the stiffness method

A: Calculate the angle:tan∅=34tan∅==36.87°Degree of freedom =5No degree of freedom at joint 1 due to…

Q: A steel bar is welded between two rigid surfaces as shown in the picture. The temperature of the bar…

Q: 100 mm 25 mm 125 mm M. 75 mm The beam is subjected to an internal moment of M = 3 kNm. 25 mm 75 mm…

Q: A steel strut S serving as a brace for a boat hoist transmits a compressive force P= 63 kN to the…

A: Given values,P=63kNt=8mθ=41°dpin=15mmtG=14mmtB=10mmdbolt=10mmCalculating bearing stress between…

Q: A vibration isolation support consists of a rod A of radius R₁ and a tube B of inner radius R₂…

A: G = 10.93 MPaP = 13 kN or 13000 N

Q: The beam shown is subjected to two loads, one point and the other uniformly distributed. Determine…

Q: A rigid plate C is used to transfer a 20-kip load P to a steel (E = 30,000 ksi) rod A and to an…

A: Detailed solution is provided below :

Q: Q.1: A shaft composed of segments AB, BC is fixed between the two walls at A and C and loaded as…

A: Given that: A composite shaft as shown -

Q: unit

Q: DEFORMATION DUE TO AXIAL FORCES PROBLEM 1: CE Brd Exam The rigid block shown weighs 176.4 «N. It is…

Q: 2.) When an axial load is applied to the ends of the bar shown, the total elongation of the bar…

A: Given:- Total elongation of the bar between joints A and C = 0.15 in Normal strain measured in…

Q: Both portions of the rod ABC are made of an aluminum for which E = 70 GPa. Knowing that the…

A: This problem is related to solid mechanics. In this problem we calculate Value of a load Q and…

Question

The rigid bar BDE is supported by two links AB and CD. Link AB is made of
aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm^2; link CD
is made of steel (E = 200 GPa) and has a cross-sectional area of 600 mm^2.
For the 30 kN force shown, determine the deflection of B and E,
respectively.
0.4 m
0.3 m
B
A
0.2 m
OC
-0.4 m
30 kN
E

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2.25. A system consists of two rigid end-plates, tied together by three horizontal bars as shown in Fig. 2-42. Through a fabrication error, the central bar, ②2, is 0.0005L too short. All bars are of identical cross section and of steel having E = 210 GPa. Find the stress in each bar after the system has mechanically been pulled together so that the gap A is closed. Ans σ-35 MPa σ = 70 MPa Fig. 2-42
Three bars AB, AC, and AD are pinned together as shown in the figure. Initially, the assembly is stress free. Horizontal movement of the joint at A is prevented by a short horizontal strut AE. Calculate the stress in aluminum bar AC and steel bar AD. Also, find the force in the strut AE when the assembly is used to support the load W = 12.50 kips. For each steel bar, A = 0.4 in² and E = 29 × 106 psi. For the aluminum bar, A = 0.8 in² and E = 10 × 106 psi. B с D 20% Steel E Aluminum 35 W A Steel L
= 29,000 For the structure and loading shown below, find the lateral deflection at the top. Use E ksi and I = 250 in4 for all members. Note that in frames, we neglect axial deformation, so you can calculate the deflection at either of the upper corners; the answer will be the same. t. 201 8K 10! 1. What is the deflection at the top in inches (two decimal places) ot
Hand written please.
The uniform beam of weight W is to be supported by the two rods, the lower ends of which were initially at the same level. Determine the ratio of the areas of the rods so that the beam will be horizontal after it is attached to the rods. Neglect the deformation of the beam. Steel 3 m E = 200 GPa Aluminum 2 m E = 70 GPa W 1.5 m -3 m- + 0.5 m
A steel strut S serving as a brace for a boat hoist transmits a compressive force P = 63 kN to the deck of a pier as shown in the figure. The strut has a hollow square cross section with wall thickness t = 8 mm and the angle θ between the strut and the horizontal is 41°. A pin through the strut transmits the compressive force from the strut to two gussets G that are welded to the base plate B. Four anchor bolts fasten the base plate to the deck. The diameter of the pin is dpin = 19 mm, the thickness of the gussets is tG = 14 mm, the thickness of the base plate is tB = 10 mm, and the diameter of the anchor bolts is dbolt = 10 mm. Determine the bearing stress between the anchor bolts and the base plate in MPa.
The two sheets of soft plastic are bonded to the central steel strip. Determinethe magnitude of the largest force P that can be safely applied to the steel strip andthe corresponding displacement of the strip. For the plastic, use tw = 10 ksi and G = 800 ksi. Neglect deformation of the steel strip.
The question is in the picture. Thanks
Two wooden studs with cross-sectional dimensions 45×145 mm2 are glued together to form a beam with a T-sectionaccording to the figure on the right and loaded according to the figure on the left. The beam is loaded in its rigiddirection.a) Calculate the moment of inertia of the cross-section about the centroid axis (z-axis).b) Calculate the maximum normal stress in the beam.c) Sketch the normal stress distribution over the most loaded cross-section of the beam. All calculations must be clear and handwritten, draw and check so that the answers are correct
SOLVE
Rigid bar ABC is supported by two aluminum alloy (E = 10,000 ksi) rods as shown below. The horizontal distance between rods (1) and (2) is a = 120 in. Rod (1) has a length of L1 = 87 in. and a cross-sectional area of A1 = 0.65 in.2. Rod (2) has a length of L2 = 84 in. and a cross-sectional area of A2 = 1.15 in.2. Rigid bar ABC is to remain horizontal under a load of P = 25 kips. Determine the distance x (in inches rounded to the nearest tenths) from joint A to the location of load P so that bar ABC remains horizontal.
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa