Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 1.9 m, b=4.8 m, P: 140 kN, WAC = 40 kN/m, and wcD = 125 kN/m. Label all significant points on each diagram and identify the maximum shear force and bending moment along with their respective locations. Additionally: (a) Determine V and M in the beam at a point located 1.5 m to the right of B. (b) Determine V and M in the beam at a point located 1.0 m to the left of D. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. WCD WAC C b Answer: Vmax= Mmax B a kN kN-m

Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 1.9 m, b=4.8 m, P: 140 kN, WAC = 40 kN/m, and wcD = 125 kN/m. Label all significant points on each diagram and identify the maximum shear force and bending moment along with their respective locations. Additionally: (a) Determine V and M in the beam at a point located 1.5 m to the right of B. (b) Determine V and M in the beam at a point located 1.0 m to the left of D. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. WCD WAC C b Answer: Vmax= Mmax B a kN kN-m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cantilever beam carries a trapezoidal distributed load (see figure). Let wB = 2.5 kN/m, WA = 5.0 kN/m, and L = 2.5 m. The beam has a modulus E = 45GPa and a rectangular cross section with width b = 200 mm and depth h = 300 mm. Use the method of superposition and Cases 1 and 8 in Table H-1 to calculate the def lection and rotation at B. WA IA L WB B
For the beam shown, the magnitude of the distributed load is w0 = 10.2 kN/m and the beam lengths are a = 4.3 m and b = 12.9 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Calculate the support reactions and draw the shear and moment diagram for each beam shown below using slope-deflection method of analysis.....
For the beam shown in the figure below, determine the equations of shear and bending moment along the beam then draw their diagrams. 21 (KN) 14 (EN) 7 (KN/m) 35CKNim) 2. 2 4 2
In figure shown, use left end of the beam as reference and assume the upward reaction provided by the ground to be uniformly distributed. (a) Write the shear-force and bending-moment equations (not simplified and simplified ) at each segment (b) draw the shear-force and bending-moment diagrams 60 kN 40 kN/m 40 kN/m C D. . Label all significant points on each diagram 1 m 1.5 m 1.5 m 1 m
Question 2 (Bending Moment and Shear Force)The simply supported beam AD is subject to a uniform load over the segment BCtogether with a concentrated force applied at C as shown in figure 1.0 below.a. Plot the shear and moment diagrams of the beam.b. If the beam has a cross-sectional area as shown in figure 2.0 below,determine the bending stress at location F
4. In the figure shown, assume clockwise as positive, compute the moment of force P = 360 kN about point moment of %3D 250 kN and P, A. P = 250 kN Q= 360 kN B.
For the beam shown, the magnitude of the distributed load is w0 = 11.6 kN/m and the beam lengths are a = 7.1 m and b = 21.3 m.(a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A.(b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the maximum shear force and the maximum bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=3.5 m, b=2.5 m, PB = 4 kN, PC = 4 kN, and MB = 60 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. Calculate the reaction forces Ay and MA acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Determine the shear force acting at each of the following locations:(a) x = 0+ m (i.e., just to the right of fixed support A)(b) x = 3.5– m (i.e., just to the left of B)(c) x = 3.5+ m (i.e., just to the right of B)(d) x = 6.0– m (i.e., just to the left of C)When entering your answers, use the shear force sign convention. Determine the bending moment acting at each of the following locations:(a) x = 0+ m (i.e., just to the right…
Find the support forces at Points A and B by showing the free body diagram of the simple beam given above (the weight of the beam is neglected). the places with i in the picture will be 4, the places with j will be 7.
Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a=3.5 ft, b=6.0 ft, MA = 15 kip-ft, w = 10 kips/ft, and PD = 6 kips. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces By and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Bx = 0, it has been omitted from the free-body diagram.)Answers: By = kips, Cy = kips. Part 2 Determine the shear force acting at each of the following locations:(a) x = 0+ ft (i.e., just to the right of point A)(b) x = 3.5– ft (i.e., just to the left of support B)(c) x = 3.5+ ft (i.e., just to the right of support B)When entering your answers, use the shear force sign convention.Answers:(a) V = kips.(b) V = kips.(c) V = kips.…
The three-bar truss ABC shown in the figure has a span L = 3 m and is constructed of steel pipes having cross-sectional area A = 3900 mm^2 and modulus of elasticity E = 200 GPa. A load P acts horizontally to the right at joint C. 1. If P = 60 kN, what is the horizontal displacement of joint B? a. 1.99 mm b. 7.50 mm c. 5.21 mm d. 2.25 mm 2. What is the maximum permissible load P if the displacement of joint B is limited to 2.5 mm? a. 85.0 kN b. 75.4 kN c. 52.1 kN d. 12.5 kN