Problem (8.5): A simple beam AB supports two concentrated loads P at the positions shown in the Figure (8.25). A support C at the midpoint of the beam is positioned at distance d below the beam before the loads are applied. Assuming that d=10 mm, L=6 m, E 200 GPa, and I=198x106 mm, calculate the magnitude of the loads P so that the beam just touches the support at C. d HH B ՏՈ L L

Problem (8.5): A simple beam AB supports two concentrated loads P at the positions shown in the Figure (8.25). A support C at the midpoint of the beam is positioned at distance d below the beam before the loads are applied. Assuming that d=10 mm, L=6 m, E 200 GPa, and I=198x106 mm, calculate the magnitude of the loads P so that the beam just touches the support at C. d HH B ՏՈ L L

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A simply supported beam with length l is loaded with a uniformly distributed load w. What is the…

A: A simply supported beam is the beam that stays on two supports and is free to move horizontally. It…

Q: The beam AB supports two concentrated loads and rests on soil that exerts a linearly distributed…

A: Step 1:Step 2:Step 3:Step 4: Hope this helps!

Q: Question 3) The rigid beam CD in the figure is attached to the ceiling with AC and BD rods. The…

A: Given data: Bar AC : L=2 mE=70 GPaD=11 mm Bar BD : L=0.7 mE=94 GPaD=25 mm Rigid beam CD L=1.5 m…

Q: A triangular distributed load of max intensity w =370 N/m acts on beam AB. The beam is supported by…

Q: W ^^ 3m 6m 3m W 6m 6m

Q: Learning Goal: To determine the shear stresses at specific locations in a beam due to an external…

Q: Situation 15 - Refer to the beam shown in the figure. Given: a=1m w = 18 kN/m P = 30 kN Flexural…

Q: A 4 m W B 2m C

A: An overhanging beam is given of length = 12m in which uniformly distributed load is acting. It has…

Q: Steel girder (A=21,100 mm²) C -8.5m- Problem 1. The floor system of an apartment building consists…

A: Given, Thickness of reinforced concrete = 100 mm Cross sectional area of floor beams = 11800 mm2…

Q: 5.2. Find the critical value of the load P Fig. 5.2 if both ends of the beam are simply supported.…

A: Using Finite differences method Euler's buckling load Pcr = π2EIL2 let L = x Pcr = π2EIx2 x Pcr…

Q: A buit-in cantilever beam with a hollow rectangular cross-section is subjected to a uniformly…

A: In the Beam main stress acting are flexural stress and transverse shear. Along the depth of the beam…

Q: steel beam is loaded as shown in the figure. Determine the following by using conjugate beam method:…

Q: Answer the problem. Structural theory

A: In this problem, we begin first by examining the given data and illustration. From a structural…

Q: Problem (8.1): A wide-flange beam (W12 * 35) supports a uniform load on a simple span of length L=14…

Q: saw-tooth loading is applied as shown in the figure. The flexural tiffness (EI) of the beam is 1×10³…

A: Given- A propped cantilever beam carrying UVL loading. Required- To calculate support Reactions of a…

Q: es a uniformly distributed load of 5 kN/m toget s free ends. 2 kN w = 5 kN/ m. 2 m 8 m the…

Q: c) the value of the maximum bending moment in the beam. Enter your answer in KNM to three decimal…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

Problem (8.5): A simple beam AB supports two concentrated loads P at the positions
shown in the Figure (8.25). A support C at the midpoint of the beam is positioned at
distance d below the beam before the loads are applied. Assuming that d=10 mm, L=6 m,
E 200 GPa, and I=198x106 mm, calculate the magnitude of the loads P so that the beam
just touches the support at C.
d
B
ՏՈ
L

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Can you please answer this question
PROBLEM 03: Determine the shear modulus of the body shown in the figure if the top and bottom surfaces is fixed to the rigid plates. If the top plate displaces 2.5mm horizontally when subjected to horizontal force P=1.5kN. The width of the block is 150mm. Assume that the body is linearly elastic and use small angle analysis. 400mm- 200mm
please confirm the answer for this.
:A beam is 10.5 m in length and loaded as shown in Figure Q4. If the deflection in the mid-distance between A and B is 3 mm, find the value of flexural rigidity (El). Find also the value and location of the maximum deflection. 1 KN/m 1 kN 3 kN D. C 6 m 2 m 2.5 m Figure Q4: Beam Loading
2 – Determine the slope and deflection at point B using the direct integration method and draw the shear force and bending moment diagrams for the beams shown in Figure 2 and Figure 3 below (Problems 6.7 and 6.10 of Structural Analysis, 6th Edition, Aslam Kassimali). A A W L El = constant Figure 2 4m El = constant E = 70GPa I = 164 (106) mm² Figure 3 B 50 kN.m B
A 3m long simply supported beam of uniform cross section is subjected to a distributed uniformly w= 20 kN/m in the central 1m as shown load of in the figure. w= 20KN/m EI = 30x106 Nm? 1m 1m 1m If the flexural rigidity (EI) of the beam is 30x10 N-m?, the maximum slope (expressed in radians) of the deformed beam is
Hw1: For the simply supported beam shown in Figure, determine the maximum deflection due to the applied load. The flexural rigidity of the beam is El= 7x106 kip.in². V₁ = 20 kips a = 12 ft 1 = 18 ft Answer: ymax = -0.129 ft downward W = 60 kips b = 6 ft 2 V₂ = 40 kips
Vertical rod CD of length L = 2 m, cross-sectional area A = 150 mm2 %3D %3D and modulus of elasticity E = 70 GPa supports a rigid beam AC of negligible weight, which, in turn, supports a uniformly distributed load over segment AB. When there is no load, the beam is horizontal. Determine wo (in kN/m) if the allowable elongation of rod CD is 15 mm. 2 m WO B. C 2 m D.
Consider the continuous beam as shown in figure below: RA 9,- 2 6 (m) R₂ What will be the magnitude of slope at B? H₂ 6 (m) Re
Question 3 (CLO#2) The beam structure shown in Figure 2 below supports a uniformly distributed load of 100 kN/m and a concentrated load of 250 kN. The beam has a box-shaped cross-section with the dimensions provided below. Determine the following: .a) The magnitudes and location of the maximum bending moment and shear force that occur in the beam. .b) The geometric centroid and moment of inertia of the box beam cross-section. .c) The magnitude and location of the maximum bending stress(es) within the beam. .d) Based on your findings from part c), determine which of the following ductile materials would be most appropriate for the design of this beam (considering strength only). Discuss your reasoning. o Material A with yield strength of 175 MPa o Material B with yield strength of 345 MPa o Material C with yield strength of 210 MPa
The two sub questions and question g as well :
A thin beam with a solid rectangular cross-section is loaded as shown in Figure Q7 below. W W L/3 L/3 L/3 Figure Q7 What is the ratio of the maximum to nominal shear stress for the beam described in Question 7? O a. 3:2 O b. 1:4 Ос. 3:1 O d.2:1 O e. 1:2 O f. None of the provided answers are correct. O 8. 1:1