Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a= 2.5 m, b= 7.0 m,MB = 85 kN-m and Mc = 130 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results toanswer the questions in the subsequent parts of this GO exercise.yMBMcВCDCalculate the reaction forces A, and Dy acting on the beam. Positive values for the reactions are indicated by the directions of thered arrows shown on the free-body diagram below. (Note: Since A, = 0, it has been omitted from the free-body diagram.)MBMcABCabaAyDyAnswers: Ay =ikN, Dy =ikN.%3D

Answered: Image /qna-images/answer/1c018601-c89d-4d5f-a6c5-ef10fcb7a589.jpg

Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a= 2.5 m, b= 7.0 m, Mg = 85 kN-m and Mc = 130 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. y MB Mc B Calculate the reaction forces A, and D, acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since A, = 0, it has been omitted from the free-body diagram.) MB Mc C A D A B b a a Dy kN. kN, Dy = i %3D Answers: Ay = i

Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a= 2.5 m, b= 7.0 m, Mg = 85 kN-m and Mc = 130 kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. y MB Mc B Calculate the reaction forces A, and D, acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since A, = 0, it has been omitted from the free-body diagram.) MB Mc C A D A B b a a Dy kN. kN, Dy = i %3D Answers: Ay = i

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Consider the beam shown in (Figure 1). EI is a constant. Suppose that w = 20 kN/m. Part A Determine the reaction at support (1) measured upward. Express your answer to three significant figures and include the appropriate units. Enter positive value if the force is upward and negative value if the force is downward. µA Q6 = Value Units Figure 1 of 1 Submit Request Answer 6. 3 Part B kmimi Determine the moment exerted by support (1 on the beam measured counterclockwise. | 1 1) Express your answer to three significant figures and include the appropriate units. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise. 3 2.5 m 5 m HA ? Q5 = Value Units
In the system whose loading status is given in FIGURE 2, taking into account only the bending effects, with "Double Integration" method;a) Cross section rotation of the beam at B point (BB) in radian unit,b) Calculate the vertical displacement (yc) of the beam at point C in mm.Beam bending stiffness (EI) is constant along the rod and its value is 10000 tm2. q=5 t/m a=2m b=5m
Item 8 Consider the beam shown in (Figure 1). Suppose that w1 = 900 N/m and w2 = 550 N/m. Part A Determine the y component of reaction at A using scalar notation. Express your answer to three significant figures and include the appropriate units. µA Ay = Value Units Submit Previous Answers Request Answer Figure 1 of 1 X Incorrect; Try Again; 4 attempts remaining Part B Determine the x and y components of reaction at B using scalar notation. Express your answers using three significant figures separated by a comma. 3m 3 m vec B B,- kN Submit Previous Answers Request Answer %23
Mc A B For the beam shown in the figure, with the depicted loading and boundary conditions, draw the shear force and bending moment diagrams – please draw your graphs with care to represent constant values, linear relationships and parabolic relationships. In your work show the reactions and respective values at A and B, the equations you obtained for shear force and bending moment distributions, and relevant values of shear force and bending moment at relevant points along the span of the beam – in your graphs. Mc = 4 kN.m P = 3 kN/m L = 1.25 m
*USE FORCE METHOD OF ANALYSIS *THE ANSWERS MUST BE IN 4TH DECIMAL PLACE Try to answer in 30mins....
A 8 m beam is fixed at one end, and hinged at the other end. The beam has constant (EI) and the load on the beam is illustrated as shown in Figure 1. Using the finite difference method, determine deflections in the beam. Take h=Ax =L/4. 9, = 40 kN/m 6m Constant El 12 m Figure 1 Find the magnitude and the location of maximum deflection of the beam in Figure 1, and then compare the results with the exact solution. If the section of the beam changed with the length, as displayed in the Figure 2, find new deflection values in this case? 50 mm 50 mm 50 mm 30 mm Figure 2
Pls answer Express your intermediate answers with at least FOUR decimal places and simplify your FINAL answers up to TWO DECIMAL PLACES. BOX your FINAL ANSWERS. Complete solution with figure. Write legibly.
Consider the beam shown in (Figure 1). The support at B can be assumed to be a roller. Suppose that w = 7 k/ft Figure 12 ft 12 ft < 1 of 1 Part A Determine the z and y components of reaction at A. Express your answers using three significant figures separated by a comma. [5] ΑΣΦ [. Az. Ay= Submit ▼ Part B Request Answer B₁ = Determine the y component of reaction at B. Express your answer using three significant figures. ΕΠΙ ΑΣΦ vec Pearson J1 vec 3 → ? ? k Revie
Kindly answer the entire question(Q3) in the image given below. For your information, the unknown,w is given as 2. w=2
Solve the given problem. Round off answers in all computations in 4 decimal places. Determine the moment capacity of the beam shown in the figure.
The beam shown in the figure is supported at roller A and pinned at B and has a uniformly distributed loading w 36 kN/m over 1.5 m from the left-hand end and moment loading M = 44 kNm at 1.5 m from end B. - Determine the reaction force at support A. Input your answer as a value only in KN to one decimal place and without +/- sign. w kN/m M kNm B A X -1.5 m -1.5 m -1.5 m-
load A =350 N load b=400 N