A steel beam, of lengths a=5 m and b=5 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q=0 kN/m to q = 5 kN/m for AB span; and is constant with q= 5 kN/m for BC span. The Young's modulus of steel is 200 GPa. y, v a 5 mm 200 mm niwm B 300 mm b с

A steel beam, of lengths a=5 m and b=5 m and a hollow box cross section, is supported by a hinge support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300 mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of the intensity that linearly varies from q=0 kN/m to q = 5 kN/m for AB span; and is constant with q= 5 kN/m for BC span. The Young's modulus of steel is 200 GPa. y, v a 5 mm 200 mm niwm B 300 mm b с

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Part A is correct but I'm not sure about part b

Q: *2-20. The piece of plastic is originally rectangular. Determine the average normal strain that…

A: In this question we have asked average normal strain that occurs along the Diagonal AC and DB.....…

Q: 1. From figure 1.1. Determine the distance 'a' as a fraction of the beam's length 'L' for locating…

A: Take moment about A∑ MA=0 3PL-RCL-a+PL6=0RC=196PLL-a∑ Fy=0 RA+RC=4PRA=4P-196PLL-a

Q: Question # 3: The built-up beam is formed by welding together the thin plates of thickness 3 mm. the…

A: Shear center is a point on the beam section where the application of loads does not cause its…

Q: Two cables AB and AC are acting on the pole with forces FAB=540N and FAC=560N with parameters…

Q: per the attached figure: a shear force of V = 448 kN is applied to the box girder. determine the…

A: A shear force of V =448 kN is applied to the box girder.Find the moment of inertia (I) of the box…

Q: A B. y Figure Q4: A cantilever beam under non-uniformly distributed load (a) The support reaction…

Q: 1. A homogeneous hemisphere of weight W and radius a rests on a perfectly smooth horizontal table as…

A: To find the tension in the string, we can use the principle of moments.. The weight of the…

Q: The piece of rubber is originally rectangular. Calculate the average shear strain Yxy at A if the…

A: Given data in question Cross section 400 mm and 300 mmDisplacements 3 mm and 2 mmTo find out Average…

Q: The rigid body shown in the figure is subjected to the indicated force system. Determine the forces…

Q: Part A Determine the magnitude of the resultant force. Express your answer to two significant…

A: Given :

Q: F 200 N F3=300N M. 100 Nm 0.4 m F, 300N 0.5 m 0.6 m The pipe system shown in the figure is supported…

Q: A non-prismatic rod is attached between two supports as shown in figure. It is subjected to axial…

A: Given :- E =200 GpaAAB= 300 mm2 =450 mm2

Q: Determine the maximum deflection of the beam. Assume that a wooden beam has a vertical deflection…

A: Ans is given below

Q: What is the value of the Horizontal reaction force at A in N? if P = 45-N. (Note: enter your numeric…

Q: Use the graphical method to construct the shear-force diagram and identify the magnitude of the…

A: We have to calculate magnitude of largest shear force of diagram by using graphical method

Question

Calculate the vertical support reaction in support B. Enter your answer in kN to two decimal places.

A steel beam, of lengths a=5 m and b=5 m and a hollow box cross section, is supported by a hinge
support A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300
mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load of
the intensity that linearly varies from q=0 kN/m to q=5 kN/m for AB span; and is constant with q= 5 kN/m
for BC span. The Young's modulus of steel is 200 GPa.
y, v
a
5 mm
200 mm
niwm
B
300 mm
b
с

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Mention the given Data

VIEW

Step 2: Calculation of vertical reaction at B

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The overhanging beam is supported at A and B and has a uniformly distributed loading w= 13.9 kN/m as shown in the figure. Determine the max bending moment in the beam. Input your answer as a value only in kNm to one decimal place without +/- sign. W C 4 m B 2m
Consider the beam shown in (Figure 1). Take P = 2 kip and w = 1.9 kip/ft. Point E is just to the right of the 2-kip load. Follow the sign convention. Figure 6 ft • D 6 ft 14. B -4 ft E 4 ft 1 of 1 Determine the shear force at point E. Express your answer in kilopounds to three significant figures. VE = Submit Part F VE| ΑΣΦ ↓↑ vec ME = Request Answer Determine the moment at point E. Express your answer in kilopound-feet to three significant figures. IVE ΑΣΦ ? vec ? kip kip-ft
In neat and clean writing
Problem 5.2 The rigid bar shown is pinned at A and supported by two steel rods, each having a diameter of 1 in. The system is subjected to a load P = 2 kip (note: kip refers to kilopound). If the bar is assumed to be rigid (meaning that it does not bend due to the loading) and is initially vertical, determine: A) The force in each bar when P is applied B) The displacement of end B when P is applied a = 1 ft, b= 1 ft D -b 2b B E AG Check your work: FEF = 1.26 kips a a a a P
0.0079 0.0032 0.0016 Let D = 0.0032 0.0063 0.0032 be a flexibility matrix, with flexibility measured in inches per pound. Suppose that forces 0.0016 0.0032 0.0079 of 10, 30, and 20 lb are applied to a beam at points 1, 2, and 3, respectively. Find the corresponding deflections y₁. Y₂, and Y3- #2 f₂ Y₁ = inch(es) (Round to the nearest thousandth as needed.) #3
Please solve and provide answers also
Please write the solution on paper.
Consider the rod shown. Suppose that hℎ = 170 mm, r = 290 mm. Determine the location (x,y) of the centroid of the rod.
300 mm 100mm -200 mm -200 mm Determine the internal forces acting at point Q. Take m= 100kg.
In the frame shown below, P is equal to 208. what is the value of the Vertical direction reaction force component at C in N? (note: enter your numeric answer only. No need to enter units. Give your answer to two decimal places) and negative to the down direction. Vertical force component at C, Cy = N 3 m 2 m -2 m- A 60° B
Example: Resolve the horizontal 600 N force in shown into and components acting along the u and v axes determine the magnitudes of these components. F 30° 130 600 lb
A structural steel rod 1(1)/(2) inches in diameter and 25 feet long, in supporting a balcony, carries a tensile load of 29k;E=29 xx10^(3)ksi. a. Find the total elongation delta of the rod. b. What diameter d is necessary if the total delta is limited to 0.1 inch?