Consider the rod shown. Suppose that hℎ = 170 mm, r = 290 mm. Determine the location (x,y)  of the centroid of the rod

Q: 1. Determine las coordenadas del centroide de la siguiente figura. 4a 3a

A: solved

Q: Q2) A rectangular block of an elastic material is subjected to normal and shear loads. The deformed…

A: Consider the free body diagram ;

Q: Determine l, and I, for the region shown. Note that the region is symmetric about the x-axis. 68 mm…

A:

Q: The piece of rubber is originally rectangular. Calculate the average shear strain Yxy at A if the…

A: Given data in question Cross section 400 mm and 300 mmDisplacements 3 mm and 2 mmTo find out Average…

Q: The cross section of a slit rectangular tube ofconstant thickness is shown in the figures.(a) Derive…

A: in the given question the basic data that is the length and width and thickness of web and flenge…

Q: A steel beam ABC is simply supported at A and B and has an overhang BC = 1.5m. AB = 3m. The beam…

A: let,RA=vertical reaction at support A in upward directionRB=vertical reaction at support B in upward…

Q: Locate the centroid of the plane area shown if a = 250 mm. y a mm 150 mm y = kx² The value of X is…

A: Consider a differential element of width dx and height (y1-y2) at a x distance from x from y-axis as…

Q: or the beam shown in the figure determine the following: (EI = constant) a. value of EIθ at A b.…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: A 60° P C -3m- 60° Prob. F6-4 OTOTO B

A:

Q: Three steel rods, each having a cross-sectional area of 500 mm2, are assembled in a symmetrical…

A:

Q: metry for the jaws. 6 mm 12 mm G 35 24 20 mmmmmm 27 N -76 mm- B 27 N

A: An applied force is the force applied to an object by someone or something else. An object is…

Q: the clamp exerts a normal force of 100N on the three pieces held together as shown. what force P may…

A: F=100N u=0.6

Q: al member is

A:

Q: Q2- Explain how to find the centroid of the area shown in figure y a a 2а За За MATHalino.com

A: Centroid: The imaginary point at which the total area of the system or body is assumed to be…

Q: 5. Determine the x component of the centroid of the given area. y A 2 y = x y=1.44-x B X

A: we have given equations y2 = x  , y = 1.44 - x    At mid of the given area, point C…

Q: A slender homogeneous wire of uniform cross section is bent into the form shown. Determine the…

A: The centroid is the center point of the the cross section or geometric center which is either one…

Q: The bar composed of aluminum was sustained by the 14 mm2 cross-sectional area of the pin-connected…

A: The given data is shown below: Cross-sectional area=14 mm2E=68.9×109 Pa

Q: Use E = 200 GPa, linear of coefficient expansion = 11.7 x 10° per degree celsius and A = 4500 mm…

A: To find out the deformation of the left rod in mm.

Q: A wooden bar beam arrangement is shown in the figure. The beam is formed by nailing wooden bar and…

A: For a wooden bar beam arrangementThe beam is formed by nailing wooden bar and each nailshearing…

Q: Locate the centroid of the area shown in the figure by direct integration. (Caution: Carefully…

A: To find the centroid of the area

Q: 8-7. A steel plate with holes cut in it is shown below. The plate has a thickness of t=6.35mm and…

A: The thickness of the section, t = 6.35 mmDensity = 8000 kg/m3To determine the coordinates of the…

Q: Determine the coordinates of the centroid of the trapezoidal area shown. Assumea = 200 mm, b= 340…

A:

Q: Calculate the depth of the neutral axis of the section in PART B in mm.0

A: Given Data: The dimension of the beam is 250 mm by 400 mm. The compressive strength is fc'=21 MPa.…

Q: 12,5:The two wooden plates are connected to each other with nails as shown in the figure. Since a…

A: It is required to find the shear force force P that the joint can carry.

Q: 9 Rev RAL RAU = 9C.L E RAV = = C १८.८. उं 9Av 'RAL 9=0 q=9c EASC Efac ¡ -. na B :( EA AB E IAB

A:

Q: .. Consider the following wooden T-beam on its side. It consists of two wooden parts glued together.…

A:

Q: let R=73mm. -The x-coordinate of the centroid is _____ mm. - The y-coordinate of the centroid is…

A: The centroid of a body is the point from which the whole weight of the body acts. All bodies consist…

Q: Locate the centroid of the figure below from x and y axis.

A:

Q: Consider the rod shown. Suppose that h = 170 mm, r = 290 mm. Determine the location (x,y)of the…

A:

Q: A torque wrench is used to tighten the nut on a bolt. If the dial indicates that a torque of 60 lb #…

A: The F.B.D diagram is given below-

Q: — 300 тт, b2 3— The section of a column is shown in the figure. The dimensions are given as: b1 180…

A: Column: A column is a structural element which transmits, through compression, the load of the…

Graphical Methods

The graphical method is a method of solving equations involving more than one variable using the Cartesian coordinate system. In civil engineering, the use of the graphical method is limited to the problems involving two variables. The graphical method has a great impact in solving the questions regarding engineering mechanics.