Determine the force P exerted on the twig G. Note that there is a horizontal line of symmetry for the handles, but there is no line of symmetry for the jaws. 9 mm 12 mm 22 N D 38 mm 26 23 mmmm B -71 mm 22 N Answer: P = i 263 N

Determine the force P exerted on the twig G. Note that there is a horizontal line of symmetry for the handles, but there is no line of symmetry for the jaws. 9 mm 12 mm 22 N D 38 mm 26 23 mmmm B -71 mm 22 N Answer: P = i 263 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem 6.2. The undeformed and deformed outline of a material element are as shown in the figure…

A: Consider the given figure 1.} Calculate γxy at corners A,B,C and D Shear strain γxy is given by…

Q: The force of F = 55 lb acts along the edge DB of the tetrahedron shown in (Figure 1). Figure 8 ft 10…

Q: der the beam shown in (Eigure 1) Set F= 50 kN. Neglect mickness of the beam

Q: Determine the total elongation of the bar shown in figure below. Materials E (GPa) Bronze 83…

Q: The vertical shear force of 20 KN is applied to the beam of cross section shown.If beam dimension H…

A: Shear force (V) = 20 KN Determine the shear stress at neutral axis of the section.

Q: A metal bar AB of length L is held between rigid supports and is heated non-uniformly in such a…

A: For a metal bar AB held between rigid supports and is heated non-uniformlyLength= LChange in…

Q: The SI unit of kinematic viscosity (v) is (a) m²/s (c) m/s² (b) kg/ms (d) m³/s²

A: The resistance of flow between the adjacent layer of fluid is called as dynamic viscosity. It is…

Q: Problem 6.2. The undeformed and deformed outline of a material element are as shown in the figure…

A: The diagram is shown below, And,

Q: A cantilever beam of solid circular cross section is 1 m long and has a diameter of 100 mm. Attached…

A: D = Diameter = 100 mm = 0.1 mL = Length of beam = 1 m

Q: PROBLEM The centroid of the T-section shown is 2.4 inches above the base and x is 15. What should be…

Q: The magnitude of the reaction exerted on the L-shaped bar at B is 70 lb. (Figure 1) Figure 17 in 14…

Q: . Which of the following comments about the spacing of the rivets i

Q: Calculate the tensile stress when applied force of 1200ON on specimen of diameter of 7mm

A: tensile stress = tesile force / normal cross section area

Q: H.S An open cylinder can has an inside radius of 2 cm and an inside height of 5 cm use the total…

Q: Three bars each made of different materials are connected together and placed between two walls when…

Q: into the parallelogram shape as shown in the figure. All edges remain the same length a, as the…

A: solution of above problem is below:

Q: A beam is subjected to equal bending moments of M₂ = 2800 N.m. The cross-sectional dimensions are b…

A: The bending moments of Mz = 2800 Nm. The cross-sectional dimensions are b = 150 mm c = 27 mm d = 72…

Q: The intensity applied to beam AB is increased by a factor of 2. (i.e. your answer for the ntensity…

Q: The thin square plate shown is uniformly deformed such that E - +1425 µE, E, - -668 uE, and ygy -…

Q: Question 8 The rigid, horizontal slab is attached to two identical copper rods. There is a gap A =…

Q: The v -t graph for a particle moving through an electric field from one plate to another has the…

Q: At room temperature of 22°C a gap of 0.4 mm exists between the ends of the rods shown. At what -…

Q: The structure shown below consists of an arc AB and an elastic column BC. The joints where the…

A: To determine the reactions at supports, assume the sum of moments about a reaction point equal to…

Q: SOALAN 4(b) M QUESTION 4(b) Determine the centroid (x,y and Z) of the component shown in Figure Q4…

Q: The surface tension of soap water is 0.04NM. The excess of pressure inside a soap water bubble of…

A: Given data : Surface tension (σ)=0.04 N/mDiameter of soap bubble (D)=10 mm

Q: 1. Show that: GE (a) k = 9G-3E 3k-2G (b) v = 6k+2G

Q: The rigid horizontal bar ABC of negligible mass is connected to two rods as shown in the figure. If…

Q: Calculate the normal stress (a) in the bar.

A: The values and diagram given in the question are as follows: Force(F)=45 kN or 45000 N…

Q: Part A If the maximum average normal stress for the washer is max = 60 ksi and the maximum average…

Q: Determine the x-, y-, and z-coordinates of the mass center of the body constructed of three pieces…

Q: 2 3 1 If A = -1 2 4 057 What is the cofactor of the second row, third column element? A. B. C. 3 1 5…

A: In this question a matrix is given and we are asked to find out cofactor of second row and third…

Q: Question 2. Find the change of temperature in steel bar only if you know the steel bar is no stress.…

Q: A steel column is supported at the top by two steel rods so as to prevent movement at the top in the…

A: Kx, Ky, and K are the effective length factors of compression members or columns. Mathematically,…

Q: Circle One Materials that undergoes plastic deformation prior to failure is said to be "brittle." 2.…

A: Questions 2. Materials that undergo plastic deformation prior to failure is said to be "brittle."…

Q: :Which statement is true .1 Molecular spacing of solids and fluids are comparable compared to each…

A: Option 4 is correct : Intermolecular spacing in case of solids is very less when compared it with…

Q: Consider a strain gradient in a cantilever beam as shown in the attached figure. VA-B- the shear…

A: Given data: VA-B=600 lbb=2 int=1 in

Q: No. Load Elongation L. P(KN) SL(mm) W. (mm) Area Ở eng (KN/m²) E eng (mm) m2 1 100 36.1 38 0.02 100…

A: Assuming square section of side W0. S.No. Load P (KN) Elongation (mm) L0 (mm) W0 (mm) Area…

Q: Which of the following is not true about the CU test OR-test O Can measure Su O quick test O Can…

Question

number of significant digits; the tolerance is +_1 in the third significant digit

Determine the force P exerted on the twig G. Note that there is a horizontal line of symmetry for the handles, but there is no line of
symmetry for the jaws.
9 mm
12 mm
22 N
D
38
mm
26 23
mmmm
B
-71 mm
22 N
Answer: P =
i
263
N

AI-Generated Solution

AI-generated content may present inaccurate or offensive content that does not represent bartleby’s views.

Unlock instant AI solutions

Tap the button
to generate a solution

Click the button to generate
a solution

SEE SOLUTION

Similar questions

Solve briefly stepwise
2. A linear spring of stiffness k N/mm is to be designed to stop a railroad car, with a mass of m kg, traveling at v, km/hr within x mm after impact. Find the smallest value of k, in terms of m, ve, and x, that will produce the desired result. Hint: a dx = v dv. mim Vo k wwwM
At a temperature of 37.4 °C a 0.49-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 128.7°C, determine the change in length of the steel rod if L = 328.25 mm and M = 215 mm. Round off the final answer to four decimal places.
Solve briefly stepwise
3. Consider iron and its elastic constants (Find them from the net or some book). An iron specimen consists of grains with texturing distribution of [110] (20%), [112] (20%), [111] (30%) and [103] (30%) (all percentages by volume) along the loading direction is serving under a static force of 10,000 N. The metal rod has a 20 mm diameter perpendicular to the loading direction. a) Find the strain response of the specimen.
Solve briefly stepwise
STRUCTURAL ANALYSIS II
Please solve. Show your solution on a paper with FBD
Four forces are applied to the machine component ABDE as shown. Determine the resultant acting at A. 200 mm A 40 mm | 50 N 20 mm 300 N 250 N 160 mm 100 mm 120 N
The channel shape cross-section and the rectangular cross-section shown in the Figure Q4 are made of materials with elastic-perfectly plastic behaviour. The yield stress of the material used for the channel shape cross-section is y=405 MPa, whereas that used for the rectangular cross- section is 0.850y. Compute the thickness of the web, t, of the channel shape section if the two cross sections have identical plastic bending moment about the z-axis. In Figure 4, h= 74 mm, b=52 mm, a-8 mm, H=74 mm, d= 52 mm Z b h Figure Q4 Z d H
Find ?? (epsilon x), ?? (epsilon y) and ? (gamma) . NOTE: ?? (epsilon x) ??? ?? (epsilon y) in mm/mm and ? (gamma) in radians. Indicate elongation or contraction for the normal strains. Use 3 decimal places. Use 2 decimal places in every solved value.