Part A is correct but I'm not sure about part b

Q: [Select] of gear B (d) the tangential acceleration

A: Given,  Normal acceleration at gear B, αB= 372.604 Radius of gear B, rb= 175mm

Q: Determine degree of external indeterminacy

A: Given data : Number of external support reaction (R)=3+1+1=5

Q: 不 k H, k2 H3 k3 NOTE: ト -ごー*

A:

Q: 8. HSS 10 x 8 x1/4 with Fy-50 ksi is selected to be used as a compression member with KL=10ft.…

A: Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: 1. Problem Solving: Solve the following situations as completely as possible, use any method that…

A: P= 250 KN W= -7x+81 KN/m Note According to the company guidelines i am able to answer only first…

Q: How can I find GH, EG and FH

A:

Q: Form the figure shown, a flexible belt placed around a rotating drum of 4-inch radius acts as a…

A: Given  Radius of drum = 4 inch  Kinetic friction= 0.7

Q: g) At what single point along the beam does this maximum occur? h) What are the values of internal…

A:

Q: alculate moment reaction at support A lculate Shear force at section 0.7 m away n free end 7000 N A…

A:

Q: Determine the forces in member CE , CF , FG and FH

A:

Q: G Problem 2 Given: 0.75 m 10.4 m |D Mass of car: 1400 kg B 1 m- m- 1.5 m-- C 2 m- Mass of trailer:…

A: Given:- Mass of car=1400 kgMass of trailer=800 kg To find:- Reactions at B, C and D

Q: Determine the centroid C of homogenous strips

A:

Q: 2" O 7) Fnd the centeroil, C =

A: The centroid of the composite area is calculated by using the following formula…

Q: A rectangle of an elastic material is deformed in the x, y plane as represented by the dashed lines.…

A: Given: E=300 MPa  and poisson ratio μ=0.4No deformation in Z directiona Normal strain strain in x…

Q: 1. Choose 1 type of statically determinate beam. 2. Divide the chosen beam into 3 spans, AB, BC, CD.…

A: Shear Force: The algebraic sum of all the forces acting on the given beam or structure or a frame is…

Q: Q3. Determine the plastic moment Mp of the cross sections shown, assuming the material to be…

A:

Q: Use the unit load method to calculate the vertical displacements at the quarter and mid-span points…

A: The given figure is shown below:

Q: For a soil sample in a natural condition, void ratio (e) is 0.67, degree of saturation (S) is 75%,…

A: Given data, Void ratio (e) = 0.67 S= 75% Gs= 2.7

Q: blem #1 D h E Cft The street-lights at A and B are suspended from the two poles as shown. If each…

A: AS PER THE GUIDELINES WE ARE SUPPOSED TO ANSWER ONLY 3 SUBPARTS IN A QUESTION. TO solve other…

Q: Find the Xp ¢ YT Зст I}1:25 cm Cocn 61.5 cm 0.75 cm

A:

Q: Solve for the member forces in the truss by the method of joints. Provide your answers in kN to one…

A:

Q: For the shape below determine the centroid relative to the x and y given. Once you have the centroid…

A: Given:b=4, h=4 and r =0.2Required:Centroid locationMoment of inertia about an axis through centre…

Q: What is the Ix and Iy of the cross-section in mm4

A: Given: Required : Ix and Iy of the cross-section in mm4

Q: Locate the centroid of the circular wire segment shown.

A: Consider the figure,

Q: Explain briefly how did we get s=sP-sFD

A: The principle of superposition states that the  total internal and external forces acting over a…

Q: There are support reactions Ay and By which both equal 3.5kN going upwards.

A:

Q: Determine the force in members GE, GC, and BC of the truss shown in Fig. 6-16a. Indicate whether the…

A: Question is based on the truss subject to hinge and roller support. Loading condition on truss and…

Q: Determine degree of external indeterminacy

A: Given data : Number of external support reaction (R)=3+2+2=7

Q: Classify the structure shown in the figure. OA. Indeterminate. 21st degree O B. Indeterminate, 24th…

A:

Q: 25mm 15 mm 90 mm 250 mm

A:

Q: What is the centroid of the given basic shape locate the centroid measured from y axis locate the…

A:

Q: 3? (KIN) GF? (kN) What is the force in member What is the force in member FE? (kN) What is the force…

A:

Q: Determine the force in each member of the truss

A: ∑MG=0-HA×4 + 5×2 + 94×4 + 212×6=0HA=414.5 kN →∑H=0HA-HG=0414.5-HG=0HG=414.5 kN…

Q: 22. From a triangular steel plate XYZ, a triangular section VWZ was cleanly cut off. What should be…

A: Value of x is to be determined for which the line YWZ remains horizontal

Q: 100 N 100 N 100 100 150 250

A:

Q: I need to find the reactions with the drawing

A: Given data in question  Overhanging beam  Determinate structure  To find out  ILD for reactions only…

Q: ممثلية التصاريح Theory of Structures Example (3): Calculate all the member forces for the truss…

A:

Q: Degree of external as well as static indeterminacy

A: Given :                         Number of members, m = 7Number of joints, j = 8Number of external…

Q: For a beam cross section W = 230 mm, effective depth = 500 mm, the number of reinforcement bars of…

A: Given- width w=230 mm, Effective depth d=500 mm, 12 mm dia bars, It is needed to find the number of…

Properties of Aluminium

Aluminum (or Aluminum) is a silvery-white in color metal. The chemical symbol of aluminum is Al and it has an atomic number (Z) of 13 in the periodic table. The aluminum name for this metal is derived from the Latin word ‘alumen’, which means bitter salt. Aluminum was discovered in the year 1825 by Hans Oersted, and later Friedrich Wöhler isolated aluminum. It is the most commonly found metal in the earth’s core, which is around 8% of the total core mass. Moreover, it is the third most commonly found element on earth after oxygen and silicon. Electron distribution of aluminum per shell is 2, 8, and 3 with a valency of 3. Atomic weight is nearly 26.9815 u.