A 9-m length of 6-mm-diameter steel wire is to be used in a hanger. It is observed that the wire stretches 18 mm when a tensile force P is applied. It is given that E= 200 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the magnitude of the force P. The magnitude of the force P is kN.

A 9-m length of 6-mm-diameter steel wire is to be used in a hanger. It is observed that the wire stretches 18 mm when a tensile force P is applied. It is given that E= 200 GPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Determine the magnitude of the force P. The magnitude of the force P is kN.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A piece of rubber as shown in figure is subjected to the displacements of 2 mm and 3 mm at corner B and D respectively. The average shear strain Yxy at corner A is 400 mm A 3 mm D 0₂1 | 0 300 mm C B 2 mm
Define Belling buckets
Q:A rigid block of negligible mass is supported by three rods as shown in figure, if a load (P) is subjected to the block, find the stress in the steel and aluminum rods. The area in addition to the properties of each material are given in Table below: E, Ea A, Aal A(mm) (mm) (Gpa) (Gpa) (mm') (mm') (kN) (Gра) 500 0.1 190 80 800 1600 1200 Steel Steel
Please explain with full detail step by step so I can understand, the answer should be 1800 ksi
A 1-m long steel bar (E = 200 GPa) of 10 x10 mm dimension fixed at one end and free at the other end is heated to 90°C from initially 30°C. What is the normal stress, in MPa, induced in the system due to change in temperature? Use a = 12 x 10-6 per °C. Encode you answer in whole number. Round your answer to 0 decimal places.
1
Shown in the figure attached is a beam. Given the loading and support condition and assuming that EI is constant for the beam, determine the (a) The equation of the elastic curve, (b) The deflection at the left end of the beam, and (c) The support reactions By and MB.
Please answer parts A to C with legible and complete solutions.
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 416 mm?, 622 mm?, and 281 mm? respectively.Determine the change in length (in mm) of the bar if P = 27177 N.The moduli of elasticity are 81.33 GPa for bronze ,73.05 GPafor aluminum , and 200.23 GPa for steel . Round off the final answer to four decimal places. Bronze Aluminum ЗР Steel 2P P 4P -0.6 m 1.0 m- 0.8 m
A rectangular block is 137 mm long in the X direction, 93 mm wide in the Y direction, and 56 mm thick in the Z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 200 kN tension in the X direction, 186 kN tension in the Y direction, and 228 kN compression in the Z direction. If v = 0.3 and E = 200 GPa, %3D determine the single uniformly distributed load in the X direction that would produce the same deformation in the Z direction as the original loading. Answer must be in kN.
MechanicsofMaterials
Q-1 A compound bar consists of a circular rod of steel of diameter 25 mm, rigidly fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given, E = 2 × 105 N/mm² and Ecu 1.2 x 105 N/mm². = Steel tube → Copper tube '25mm 2.5mm