Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 2.4 m, b = 4.8 m, c= 3.2 m, P= 27 kN, w = 42 kN/m, and Q = 17 kN. Label all significant points on each diagram and identify the maximum shear force and bending moment along with their respective locations. Additionally: (a) Determine Vand Min the beam at a point located 0.90 m to the right of B. (b) Determine V and Min the beam at a point located 1.00 m to the left of C. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. В D b Answer: Vmax = kN Mmax = kN-m (a) Vx1 = kN Mx1= kN-m (b) Vx2 = kN Mx2 = kN-m

Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 2.4 m, b = 4.8 m, c= 3.2 m, P= 27 kN, w = 42 kN/m, and Q = 17 kN. Label all significant points on each diagram and identify the maximum shear force and bending moment along with their respective locations. Additionally: (a) Determine Vand Min the beam at a point located 0.90 m to the right of B. (b) Determine V and Min the beam at a point located 1.00 m to the left of C. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. В D b Answer: Vmax = kN Mmax = kN-m (a) Vx1 = kN Mx1= kN-m (b) Vx2 = kN Mx2 = kN-m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the following unknowns on the beam shown below using DOUBLE INTEGRATION METHOD. Consider 150mm x 150mm section and E = 200 GPa. Show complete and organized solution. Solve the following: - Deflection at point B - Deflection at point E - Slope of the elastic curve at point D in degrees.
For the beam shown, the magnitude of the concentrated load is P = 27 kN, the magnitude of the couple is MB = 170 kN·m, and the beam lengths are a = 6.4 m and b = 19.2 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
For the beam shown, the magnitude of the concentrated load is P = 23 kN, the magnitude of the couple is MB = 350 kN·m, and the beam lengths are a = 7.2 m and b = 21.6 m.(a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A.(b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. Part 1 Cut a cross-section through the beam at variable distance x, where 0 < x < a. Derive equations for the shear force V and…
Problem 1: The cantilever truss is loaded as shown. All loads are applied normal to the top chord. Use the following values: F = 32 kN as well as A = 2,000 mm? and E = 200,000 MPa for all members. Compute the vertical displacement at point A using Virtual Work Method. Round off your answer to 2 decimal places. F E F F 3 m F = (32 kN) B -2 m D -2 m 2 m
For the beam shown, the magnitude of the concentrated load is P = 28 kN, the magnitude of the couple is MB = 230 kN·m, and the beam lengths are a = 5.8 m and b = 17.4 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Consider the beam given in the figure. Given: X= 18 kN and Eis constant. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. w = 4 kN/m 21 6 m B hinge 3 m. C 1 6 m -3m- AD Draw the shear and moment curves for the beam given in the figure.
Q1: The horizontal rigid beam ABCD is supported by vertical bars BE and CF and is loaded by vertical forces P = 400 kN and P2 = 360 kN acting at points A and D, respectively (see figure). Bars BE and CF are made of steel (E = 200 GPa) and have cross-sectional areas ABE = 11,100 mm² and Acp = 9,280 mm². The distances between various points on the bars are shown in the figure. Determine the vertical displacements &, and ôp of points A and D, respectively. E1.5m 1.5 m 2.1 m – A P = 400 kN 2.4 m P2 = 360 kN F 0.6 m|
For the beam and loading shown, use the double-integration method to determine (a) the equation of the elastic curve for the cantilever beam, (b) the deflection at B, (c) the deflection at the free end, and (d) the slope at the free end. Assume that EI is constant for the beam. Let w = 13 kN/m, L = 3.5 m, E = 175 GPa, and I = 115 x 106 mm4
A part of slab is given in the figure. The slab is supported by secondary beams AB, CD and EF which are placed with a 50cm spacing. The secondary beams transfer the load they carry to the main beams.In the figure, AE and FB are the visible part of the main beams. Finally, main beams are supported by the columns at both ends. The slab is under uniformly distributed load q=4.5 kN/m2. The span length L is 3,5 m. Determine the dimendions of rectengular cross-sections of timber beams CD and the main beam which has a length of 4 m.
Learning Goal: A beam with length L = 2.9 m is supported by a pin joint at A and a cable attached at C as shown in (Figure 1). It is subjected to the distributed load with w₁ =1.7 kN/m and w₂ = 2.1 kN/m. The angle between the cable and the beam is 0 = 35°. Determine the normal force, shear force, and bending moment acting at point B, located x = 0.6 m to the left of the end of the beam. D Wi W2 C B L Begin by finding the support reactions for the beam using the free-body diagram shown in (Figure 2). What is the tension in the cable? Express your answer to three significant figures with appropriate units What is the horizontal reaction force at A? Assume the forces acts in the direction shown, and use an appropriate sign. Express your answer to three significant figures with appropriate units. What is the vertical reaction force at A? Express your answer to three significant figures with appropriate units. Now calculate the internal loading at point B using the free-body diagram of…
For the beam shown, the magnitude of the concentrated load is P = 12 kN, the magnitude of the couple is MB = 150 kN·m, and the beam lengths are a = 4.7 m and b = 14.1 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
Calculate the vertical support reaction in support A. When sketching FBD, set the positive directions of both reactions in the positive direction of y axis. Enter your answer in kN to three decimal places.