Calculate the vertical support reaction in support A. When sketching FBD, set the positive directions of both reactions in the positive direction of y axis. Enter your answer in kN to three decimal places. A steel beam, of lengths a=5 m and b=5 m and a hollow box cross section, is supported by a hingesupport A and roller support B, see Figure Q.1. The width and height of the cross section are 200 mm and 300mm, respectively, and the wall thickness of the cross section is 5 mm. The beam is under a distributed load ofthe intensity that linearly varies from q=0 kN/m to q=5 kN/m for AB span; and is constant with q= 5 kN/mfor BC span. The Young's modulus of steel is 200 GPa.y, va5 mm200 mmniwmB300 mmbс

Calculate the vertical support reaction in support A. When sketching FBD, set the positive directions of both reactions in the positive direction of y axis. Enter your answer in kN to three decimal places.

Calculate the vertical support reaction in support A. When sketching FBD, set the positive directions of both reactions in the positive direction of y axis. Enter your answer in kN to three decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. 1 For the beam shown below, (a) Draw the V-Diagram (b) Draw the M-Diagram (c) Find the largest value of o, and give the (x,y,z) coordinates of its location. (d) Find the largest value of 7y and give the (x,y,z) coordinates of its location. List of beam properties List of displacements List of forces of single-point constraints (these are the reactions at the supports) List of forces in beam elements List of stresses in beam elements S = 0.05" Si = 0.04" 30" Cross section Aluminum 50.000 in.lb E- l0xIo psi V=0. 3 60"
Question 3 Determine the deflections in horizontal and vertical directions at point C and the reactions at supports A and B of the truss shown in Figure (3) using the stiffness method. Take E = 210 GPa and A = 170 mm² for all members. 24 KN 3.00 m 4.00 m Figure (3) C B 18 KN
Learning Goal: To determine the reaction forces at supports on a horizontal beam by using the equations of equilibrium for a static application. As shown, beam ABC is supported by the roller at A and pin at C. The geometry of the beam is given by a=2.0a=2.0 ftft, b=6.0b=6.0 ftft, and c=11.0c=11.0 ftft. The applied forces are F1=1.50F1=1.50 kipkip and F2=2.00F2=2.00 kipkip. Force F1F1 is applied at an angle θ=35∘θ=35∘ with the horizontal. Neglect the weight of the beam. Determine the vertical reaction at A. Determine the horizontal component of the pin reaction at C. Determine the vertical component of the pin reaction at C.
Solve for the reactions, the midspan deflection, and the slope at the midspan. Use E = 70 GPa and I = 100 x 106 mm4 Final Equations with value of C1 and C2 EIy'' = EIy' = EIy = RA: RB: MA: Deflection: Slope:
What is the VERTICAL and HORIZONTAL reaction of the support at B?use :x = 137y = 37a = 6b = 8c = 1
Please solve it fast. Within 20-30min
Two forces of the same magnitude P enter a cube on side a according to the figure. Determine the equivalent force coupling system at point A.
P (kN) d (mm) t (mm) www 85 80 25 The beam in Figure Q2(a) has a cross-section as shown in Figure Q2(b), where the values of P, d and t are given in Table Q2. (a) Determine reactions, RA and Rg. (b) Determine the shear force at section AB and bending moment at point B. (c) Determine the neutral axis and moment of inertia of the cross section of the beam (d) Det hine the maximum tensile and compressive bending stress the beam at point B. (Formula: omax =). Then, plot the bending stress distribution. (e) Determine the maximum shear stress of at section AB. (Formula: T =). P (kN) t (m d (mm) 1.6 m 0.8 m d (mm) t (mm) t(mm) (a) Figure Q2
Two forces 5 CN and 10 CN are acting at a point as shown in Figure 3. The 10CN and 5 CN make angle equal to 300 and 450 with positive/negative x-axis, respectively. Solve for the moment of the resultant of these two forces about point O. Note: C represents the class number which is equal to = 4740 and N is newton.
Determine the resultant force at A. for the figure below Hint : 1- Find the position of all points A,B,C (x, y, z) 2- Find FAB and FAC 3- Find IrAnl and ITacl 4- Find FAB = F UAB and FAC = F UAC 5- Finally find R and a, ß,y %3D %3D 3m Fc= 500N FB= 500N 3m 5m 3m B 4m 2m 5m