F=2580 lb 4 A 28 ft В 2) Find the resultant force from the force reactions found at B in problem 1. (Provide size and direction with the angle to the +x axis.)

Q: 22 Situation 1: The 300-lb force is to be resolved into components along lines a-a' and b-b'. a 300…

A:

Q: Determine the magnitude of the force F given that its moment about the axis BC is 150 N-m. -4 m- В C…

A:

Q: Q2: Determine the magnitude of the resultant moment about A. Also, find the location of the…

A:

Q: 8. Find the total static indeterminacy of the following: (b) (a) (d) (c) (e)

A:

Q: A force and a couple are applied as shown to the end of a cantilever beam. (a) Replace this system…

A: a) Draw FBD of the given system:

Q: IS

A:

Q: couple moment acting at Point B: 4m 19*N с + B 2m *N/m Determine: a) The component of the resultant…

A: A simply supported beam is loaded as follows(a) resultant force in x-direction=?(b) resultant force…

Q: F 29 E 29 * Find: reactions & Force in all members a 9

A:

Q: y | 1 A -X 25' 15⁰ 40° C F = 13 kips 15' B 11 .n

A:

Q: Find the moment of force at the point x. 50 N 60 200 mm 45 100 mm X 100 mm

A: To get to the moment of force at point X, we have to resolve the force.

Q: e the magnitude of the re

A: Given:- FB= 700 N, FC= 560 N To find:- the magnitude of the resultant force and  the direction…

Q: Q2: The 300 N force as shown in figure acts on the point O. Resolve this force into two components…

A: Let us first find all the angles

Q: Az reaction at A, horizontal component Ay reaction at A, vertical component A X 6 m Press [ESC] to…

A:

Q: The force, F = (17i+ 27j + -79k) lb, is attached at the end of a pipe at point, (-20, 15, 43) ft.…

A: The given figure is shown below:

Q: C G. F y P D 600 mm A 500 mm m 360 mm

A:

Q: Find the resultant of the three forces if partical A lies on x-y plane and is acted on by the three…

A: To find resultant force

Q: The bar shown below is inclined at 45 degrees with the horizontal and at equilibrium. The force at C…

A: Given: Pb = 60 KN Pd= 40 KN Inclination angle = 45°

Q: The ends of the triangular plate are subjected to three couples. Determine the magnitude of the…

A: Given:-  The ends of the triangular plate are subjected to three couples. Determine the magnitude of…

Q: 2. Consider following beam: Given: F(Ay) = 645 N 600 N 1000 N B కా D -7.5 m- 1m a) Determine…

A: Given : - A beam is shown with F(Ay) = 645 N  Uniformly distributed load of 600 N between A to C…

Q: Two forces having a magnitude of 1000 N and 600N act on the ring. Determine the arigle 0 between the…

A:

Q: Determine if the given structure is statically determinate, statically indeterminate or unstable.

A:

Q: 2. Find the reaction at B. Hint: A is a pin, B is a roller 40 lb 50 lb 10 in. 30° 4 in. B 20 in. A

A: Given: L = 20 in H = 10 in Vertical load  = 40 lb Horizontal load = 50 lb To find: The reaction at B

Q: If force f = 600N, determine the components of the forces at B, C and D. Draw the FBD of each member…

A: Given: The value of force F is 600 N. Consider the figure,

Q: L L Determine the moments at fixed ends 'a' and 'd'?

A: Due to symmetry of frame we can cut it in half-

Q: Solve the resultant of the given concurrent forces.Given angle = 30 degrees

A: From the given question it is required to determine the resultant of the given concurrent forces.

Q: Q2/ Determine the resultant moment of the force about point D F=400N 100 N D 30 A B 45° 0.3 m 100 N…

A:

Q: Use the Müller-Breslau principle to sketch the influence lines for the vertical reaction at A, the…

A: Use the Müller-Breslau principle to sketch the influence lines for the vertical reaction at A, the…

Q: For the distributed loads shown (System 1). a) Reduce the distributed loads to three concentrated…

A: The beam must be in equilibrium and for that it has to fulfill conditions which area as follows:…

Q: 4) Determine the support reactions for the system shown. There is a pin at A and a roller at B. The…

A: Load 1000 NSpan 4 mSimply supported beamTo find out REactions

Q: The force that will balance the resultant force is called equilibrant. It has the following…

A: Ans is (b)

Q: Determine the degree of indeterminacy. *

A: It is required to determine the Degree of Indeterminacy of the following frame:

Q: 3. Find the resultant and coordinates of the intersection of its line of action with the xz plane.…

A:

Q: 3. Determine the reactions forces at A and B and all other member forces. 1200# G A F D 121 B

A: To find: Reaction forces at A and B and other member forces.

Q: The force vector F points along the straight line from point A to point B. Its magnitude is 25 N.…

A:

Q: The magnitude of the force P is 772 N. Determine the magnitude of the moment (Nm) of P about the…

A: Given: P=772 N

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.