Uoutlet Doutlet Dinlet Ax Uinlet

Q: 9. The orifice in Fig. 57 is 2 in. in diameter and is sharp-edged with - 0.63 and C, = 0.97. The…

A:

Q: diameter of 500 mm, 1.3 meters above t at a horizontal distance of 3.5 meters

A: Data we have    Diameter D = 75mm = 0.075m   Area ,A = π /4 D² = π/ 4 (0.075)² =4.4179*10³ m²   h =…

Q: A reservoir like the one shown has SAE10 oil at 20 C and is connected to a capillary tube for…

A: Neglect major and minor losses

Q: Propose a centrifugal pump (brand and model) to transport 10 L/s of a fluid with a density of 1500…

A: The discharge of the pump given at starting is- The head given is .The density of the fluid is .

Q: What is the theorical fan power needed to develop a pressure of 7.5 cm water gage W.G. supplied to…

A:

Q: milar centrifugal pumps are connected in series. The theoretical hea elation of Pump#1 is given by:…

A:

Q: Consider a desired pump operating condition which adds 35 psi at a flow rate of 500 gpa to water.…

A: Given data  Pressure = 35 psi Flow rate = 500 gpm Density of water = 62 lbs/ft^3 Find the pump head…

Q: The volumetric flowrate of CCl4 (? = 0.659 g/cm3) in a pipe is 5.39 L/s. Find:a.the mass flow rate…

A:

Q: The diagram in figure mm diameter to a very large tank where the free water surface is assumed to…

A:

Q: Water flows into a house by means of a pipe with an inner diameter of 2,4cm, absolute pressure is…

A:

Q: a. If the water volumetric flow is 0.005 m³/s and the pipe diameter is 10 cm, determine the Reynolds…

A:

Q: 34. A pressurized tank contains saturated water. A frictionless valve on the pipe is now opened to…

A: Given Data:Note:

Q: A tank is full of water and open at the top. There is a frictionless nozzle near the bottom (30 feet…

A:

Q: You were asked to design a water storage tank for your processing plant. The tank is…

A:

Q: norizontal

A: given:

Q: Water at 20°C is to be pumped from Reservoir 1 to Reservoir 2 at a rate of 3 m³/min through a 2000 m…

A:

Q: What power can be delivered by the turbine if its efficiency is 100%? The water flow rate is 0.01…

A:

Q: A Horizontal tube has a diameter of 7 in., in which alcohol (spec. grav. = 0.80) is flowing at the…

A:

Q: A piston PDP has a 5-in diameter and a 2-in stroke andoperates at 750 r/min with 92 percent…

A: Given data as per the question diameter =2 in stroke =5 in volumetric efficiency =92 % Calculations…

Q: I need complete solution (step by step process) with given. Thanks Note: Instead of using g = 9.81…

A: Hl=1.39 mL=40 mf=0.012Q=600 L/s =0.6 m3/sg=9.806 m/s2

Q: On a single plot, plot three curves that show the relationship between the pressure generated by the…

A:

Q: 03: There are three connected pipes (38 m length of 5 cm pipe diameter),. (23 m length of 15 em pipe…

A: The relation is used to determine the power  PT=ρgQ(h-hL) Here,  PT is the power extracted by the…

Q: Shown below is an inverted U-tube which is used to drain alcohol from a tank reservoir. The bend of…

A:

Q: Find the actual flow rate, assuming Ca is 0.78.

A: Given that: Inlet diameter of the venturimeter = 350 mm = 0.35 m Therefore inlet area = a1=π40.352…

Q: Q2 .. h, are 12m. The pump efficiency is 79%, and the pump is driven by an electric motor. A pump…

A:

Q: A pipeline with diameter of 0.2 m. If the inlet pressure = 2400 kPa, outlet pressure = 2300 kPa,…

A: The length of the pipeline.Given:The diameter of the pipeline is .The inlet pressure is .The outlet…

Q: 8. For the system shown below, calculate (a) the volume flow rate of water from the nozzle and (b)…

A:

Q: The inlet pressure to a piping system is 440 kPa. The inlet pipe diameter is 0.6 m. What is the…

A:

Q: ( 350 L/min) of oil (r.d -0.9 and u =0.0574 Pa.s )flow through a pipe line 75 mm) in diameter…

A: Discharge, Q= 350 L/min= 3501000(60) m3/s= 0.35060 m3/s Relative density of oil, r.d= 0.9 Density of…

Q: In a test of the centrifugal pump shown in Fig. , thefollowing data are taken: p1= 100 mmHg (vacuum)…

A: Convert 100 mmHg = 13332 Pa, 500 mmHg = 66661 Pa, 180 gal/min =0.01136 m3/s.  Calculate the inlet…

Q: What is the resulting flow rate in the system if three pumps are used in parallel? (a) 0.483 m^3/s…

A: It is given  in the question that the pumps are connected in parallel. And we know that when one or…

Q: Q.3 b) A total of 14 litres per second of oil is pumped through two pipes in parallel, one 12 cm in…

A:

Q: Consider a positive displacement pump; Shaft speed is 1800rpm Pump push 0.003gal/revolution Leakage…

A:

Q: r=20mm, the friction factor , the shear stress at pipe wall and the head loss per meter of the pipe…

A: Given: s=0.85 ρ=850 kg/m3ν=1.8×10-5 m2/sD=100 mmQ=0.50 L/sTo determine:Center line velocityvelocity…

Q: Air at 110°F passes through a -in-diameter orifice having a flow capacity constant of 3.5. If the…

A:

Q: re, a flow rate of 2 m3/s is active in a pipe, as seen in the attached figure. What is the expected…

A:

Q: 10.The nozzle shown in the figure creates a horizontal jet of alcohol ( s = 0.79) which strikes a…

A:

Q: a) The mass flow rate of alcohol. b) The pressure at section (1) if there is no losses in the…

A:

Q: The total head of fan is 200m and has a static pressure of 201mm of water gage. What is the velocity…

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.